TP-Link vigi C445 Quick Start Manual

Quick Start Guide
*Images may differ from actual products.
Φ6 mm Φ3.5 mm
Network Camera Anchors & Screws
Waterproof Cable
Attachments
1
Wall/Ceiling Mounting
1. Drill Holes
Stick the mounting template to the desired mounting place. Drill 4 screw
holes and 1 cable hole (for the cable through wall/ceiling) according to the
template.
3. Secure the Camera
Option 1: Route the cable through the wall/ceiling. Insert anchors into the
holes and use screws to affix the camera base. Identify the groove and
alignment ridge on the camera. Begin by aligning the base's rim with the
camera's groove, attaching the ridge side first for a correct fit. Once aligned,
proceed to snap the rest of the camera onto the base to secure it.
4. Adjust the Surveillance Angle
Use the L-shaped hex metal screwdriver to loosen the hex screw on the
base, and adjust the surveillance angle as needed.
Tilt: 0° to 85°
Rotate: 0° to 360°
Installing Waterproof Cable Attachments
Install the waterproof cable attachments for the network interface if needed.
Note: Make sure each part is securely attached and the waterproof rings are flush to keep out water.
Fix Nut Waterproof Waterproof
Ring Jacket
1. Route the network cable through the following components in order: fix nut,
waterproof ring, and then the waterproof jacket.
2. Fix the O-ring to the network interface of the camera and connect the network
cables.
3. Attach the network interface with the waterproof jacket, then twist to lock.
4. Insert the waterproof ring into the waterproof jacket. Rotate the fix nut to
secure it to the waterproof jacket.
Quick
Start
Guide
Mounting Template Quick Start Guide
L-shaped Hex Metal
Waterproof Seal
Screwdriver
Appropriate drilling size (Φ)
When installing with anchors
Φ = 6 mm (15/64 in.)
When installing with screws only
Φ = 3 mm (1/8 in.)
Cable Hole
(For the cable through wall/ceiling)
Rim
Alignment Ridge
Pan: 0° to 360°
Network
O-ring
Interface
Appearance
Camera Base
1
2
Unfasten the two fixed screws to remove the
cover. Press for 5 seconds to reset the
camera to factory settings.
microSD Card Slot
Unfasten the two fixed screws to
remove the cover. Insert a
microSD card for local storage.
Initialize the SD card via VIGI app
or other management tools
before recording videos.
Built-in Microphone
4
White LED × 4
5
IR LED × 4 Speaker
6 7
*The camera's standard power supply is 12V DC or PoE (802.3af/at). The power
source should comply with Power Source Class 2 ( PS2) or Limited Power
Source(LPS) of IEC 62368-1.
2. Open the Camera Case
Use the L-shaped hex metal screwdriver to loosen the hex screw, and use a
screwdriver to gently pry open the camera case. .
Option 2: Route the cable through the side outlet. Insert anchors into the
holes and use screws to affix the camera base. Identify the groove and
alignment ridge on the camera. Begin by aligning the base's rim with the
camera's groove, attaching the ridge side first for a correct fit. Once aligned,
proceed to snap the rest of the camera onto the base to secure it.
5. Tighten the Hex Screw
Tighten the hex screw to secure the camera to the camera base. Hold the
camera and ensure the camera and base are as close together as possible
when tightening.
Install Waterproof Seal for Power Connectors
Install the waterproof seal for the power connectors when using a power adapter
to power the camera.
Male Power Connector Waterproof Seal
1
2
3
4
6
5 6
Power Supply Interface
9
(12V DC) *
Side Outlet
Rim
Alignment Ridge
Female Power Connector
8
9
7
5