1. Manuals
  2. Brands
  3. TRENDnet Manuals
  4. Wireless Router
  5. TEW-212APBO
  6. Quick installation manual

TRENDnet TEW-212APBO Quick Installation Manual

Wi-fi inter-building router
Hide thumbs Also See for TEW-212APBO:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual

TEW-212APBO

Wi-Fi Inter-Building Router

Quick Installation Guide

Advertisement

Table of Contents
loading

Related Manuals for TRENDnet TEW-212APBO

Summary of Contents for TRENDnet TEW-212APBO

  • Page 1: Tew-212Apbo

    TEW-212APBO Wi-Fi Inter-Building Router Quick Installation Guide...

  • Page 2: Table Of Contents

    TEW-212APBO Quick Installation Guide TEW-212APBO _____________________________________ 1 INTRODUCTION _______________________________ 3 HARDWARE REQUIREMENT LIST ______________ 4 CONNECT AND POWER UP THE ROUTER _______ 5 Mounting the router ____________________________________ 5 Connect to the power source and the local network ___________ 6 CONFIGURING A SETUP COMPUTER ON THE LAN...

  • Page 3: Introduction

    TEW-212APBO Quick Installation Guide 1. INTRODUCTION This document is designed to provide information for the quick deployment of TEW- 212APBO Inter-Building Router. What you need to know The audience should be familiar with: Basic TCP/IP networking technology...

  • Page 4: Hardware Requirement List

    TEW-212APBO Quick Installation Guide 2. HARDWARE REQUIREMENT LIST When setting up the TEW-212APBO inter-building router, you will need the following: • TEW-212APBO Inter-Building Router • Mount kit • TEW-212APBO Router CD with documentation Additional Requirement • A computer connected to the same network as the router.

  • Page 5: Connect And Power Up The Router

    3.1). (Note: In some units, the directional flat panel antenna is embedded within the enclosure; the best reception will be directly through the front panel). Figure 3.1: Adjusting TEW-212APBO for best reception Step 4 Secure the unit in the position.

  • Page 6: Connect To The Power Source And The Local Network

    TEW-212APBO Quick Installation Guide Connect to the power source and the local network Step 1 Connect the Ethernet cable from the TEW-212APBO router to the port on the POE (Power over Ethernet) host (PH-110 Power LAN 1 port hub) labeled P-LAN OUT.

  • Page 7: Configuring A Setup Computer On The Lan

    TEW-212APBO Quick Installation Guide 4. CONFIGURING A SETUP COMPUTER ON THE LAN To configure TEW-212APBO at first time, you should prepare one computer for the TEW-212APBO setup. The operating system of this computer can be Windows, Linux or MAC with standard browsers (e.g., Netscape Navigator or Microsoft Internet Explorer versions 4.0 or later).
  • Page 8 TEW-212APBO Quick Installation Guide After setting these values on the LAN connected computer, the initial setup process, as described in the next section can be started.

  • Page 9: Setup Wizard

    TEW-212APBO Quick Installation Guide 5. SETUP WIZARD After a TEW-212APBO router is connected to your network, you can begin to manage the router through a standard web browser. To use a browser to setup TEW-212APBO, follow these steps: 1. Launch a web browser on a computer connected to the network.

  • Page 10: Device Mode Settings Page

    (described in the following section). Device Mode Settings Page The first page of TEW-212APBO configuration wizard is dedicated to the device operating mode selection. TEW-212APBO supports three different operating modes, AP (Access Point)-Router, AP and Bridge. Please refer to TEW-212APBO User’s...

  • Page 11: General Settings Page

    Host Name, Address, and Coordinates are filled in accordingly. It will make easier identification of the routers. (For detailed explanations on the parameters, please see the TEW-212APBO User’s Guide - Section “General Settings page”).

  • Page 12: Network Settings Page

    AP-Router Mode In the AP-Router mode, LAN (Local Area Network) and WAN (Wide Area Network – in TEW-212APBO it can be the enterprise network on the Internet) configuration is done using LAN Settings and WAN Settings tables shown as followed:...
  • Page 13 The masquerade setting enables the NAT (Network Address Translation) feature of TEW-212APBO. When this option is enabled, TEW-212APBO “hides” the LAN addresses to the “external” IP networks connected through the WAN interface. Direct access to the services provided by servers on the local network can be provided by using the port forwarding feature.

  • Page 14: Wireless Device Settings Page

    TEW-212APBO Quick Installation Guide AP / Bridge Mode In AP and Bridge modes, TEW-212APBO has no active LAN (Local Area Network) interface, so the “LAN Interface Settings” table is not displayed. Network settings page 2 (AP or Bridge mode) Wireless Device Settings page...
  • Page 15 TEW-212APBO Quick Installation Guide In this page, at least two essential pieces of information are required: Access Point SSID (Service Set Identifier) is a case-sensitive identification parameter for your radio network. Default Channel for BSS - It can be set up by selecting a fixed channel from the pull-down menu.

  • Page 16: Redirection Service

    01:23:45:67:89). WEP encrypts each frame transmitted from the radio using one of the keys entered from this table. Click on the “Save settings” button to save and finish configuring TEW-212APBO. Redirection Service After clicking on the “Save settings” button to end the configuration process, a waiting and redirection message should appear as shown below.

  • Page 17: Quick Test (Post Setup)

    Now you should see the following screen, click Scan to search: The utility will search and display all TEW-212APBO devices on the network. If the router has been setup successfully, it should appear in the table with the configured IP address.

Table of Contents