Installation Instructions; Unpack The Beverage Center - Jenn-Air JUB24FRACX Use & Care Manual

Overlay Frame - Rear View
Create the custom overlay frame using the dimensions shown.
IMPORTANT: The following graphic shows a custom frame for a
door with the hinges installed on the right-hand side. If your
refrigerator has the hinges installed on the left-hand side, rotate
the custom frame 180° so the hinge markings will be on the left.
⁷⁄₁₆ ³⁄₈
¹⁄₂
1 1
"
" "
(3.55 cm) (3.8 cm) (8.2 mm)
¹⁄₄
2
"
(5.7 cm)
⁵⁄₃₂
"
¹⁄₂
"
(4.0 mm)
(1.0 cm)
³⁄₈
1
"
(3.42 cm)
⁵⁄₁₆
2
"
(5.9 cm)
3
(8.5 cm)
³⁄₈
3 "
(8.5 cm)
¹⁄₂
23 "
(59.6 cm)
³⁄₁₆
30 "
(76.6 cm)
⁷⁄₈
2 "
(7.4 cm)
¹⁵⁄₃₂
A. Drill holes using a " (12 mm) drill bit to a depth of approximately
¹⁄₂
" (13 mm) before routing. (4 holes total)
⁵⁄₁₆
B. Drill holes using a " (8 mm) drill bit to a depth of approximately
¹⁄₂
" (13 mm) before routing. (4 holes total)
⁷⁄₆₄
C. Drill holes using a " (2.8 mm) drill bit to a depth of approximately
¹⁄₂
" (13 mm). (12 holes total)
D. Rout shaded areas for hinges to a
E. Rout shaded areas for hinges to a
¹⁄₈
F. Corner radius of " (3 mm) using a
(5 radiuses total)
6
¹⁄₂
"
(1.1 cm)
A B
¹⁄₂
1
"
(3.8 cm)
D E
³⁄₈ ³⁄₈ ³⁄₈ ³⁄₈ ³⁄₈
" 3 " 3 " 3 " 3
(8.5 cm) (8.5 cm) (8.5 cm) (8.5 cm)
¹⁄₂
1
"
(3.7 cm)
18"
(45.6 cm)
³⁄₈
3 "
(8.5 cm)
³⁄₄
23 "
(60.3 cm)
¹⁹⁄₃₂
" (15 mm) depth.
¹⁄₄
" (4 mm) depth.
¹⁄₄
" drill bit when routing

Unpack the Beverage Center

C
Use two or more people to move and install
beverage center.
Failure to do so can result in back or other injury.
F
Remove the Packaging
Remove tape and glue residue from surfaces before turning
¹⁄₈
" 2 " on the beverage center. Rub a small amount of liquid dish
(5.2 cm)
soap over the adhesive with your fingers. Wipe with warm
water and dry.
Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your beverage center.
For more information, see "Beverage Center Safety."
Dispose of/recycle all packaging materials.
When Moving Your Beverage Center:
Your beverage center is heavy. When moving the appliance
for cleaning and service, be sure to cover the floor with
cardboard or hardboard to avoid floor damage. Always pull
the appliance straight out when moving it. Do not wiggle or
"walk" the appliance when trying to move it, as floor
damage could occur.
Clean Before Using
After you remove all of the packaging materials, clean the inside of
your beverage center before using it. See the cleaning instructions
in "Beverage Center Care."
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
INSTALLATION
INSTRUCTIONS
WARNING
Excessive Weight Hazard