Toro 30834 Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. 30834
  6. Operator's manual
Toro 30834 Operator's Manual

Toro 30834 Operator's Manual

27" rotary cutting deck groundsmaster 3500, 4500/4700 traction unit
Hide thumbs Also See for 30834:
Table of Contents

Advertisement

Quick Links

Download this manual
Form No. 3354–410 Rev A
27, Rotary Cutting Deck
)
Groundsmaster
3500, 4500/4700 Traction Unit
Model No. 30834—260000001 and Up
Operator's Manual
English (EN, GB)

Advertisement

Table of Contents
loading

Related Manuals for Toro 30834

Summary of Contents for Toro 30834

  • Page 1 Form No. 3354–410 Rev A 27, Rotary Cutting Deck Groundsmaster 3500, 4500/4700 Traction Unit Model No. 30834—260000001 and Up Operator’s Manual English (EN, GB)

  • Page 2: Table Of Contents

    ......Dealer or Toro Customer Service and have the model and serial numbers of your product ready. The model and serial Setup .

  • Page 3: Safety

    Safety Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 98-7818 1. Warning—torque the blade bolt to 85–110 ft.-lb (115–149 N⋅m). Read the operator’s manual for further instructions.

  • Page 4: Specifications

    Specifications Note: Specifications and design subject to change without notice. General Specifications Welded 7 GA (.1793 in.),10 GA (.1345 in.) and 12 GA (.1036 in.) steel. Spindle support is 3/16 in. high-strength steel and 10 GA exterior channels, withstands Chamber Construction multiple blade impact tests.

  • Page 5: Dimensions

    Dimensions Overall length 34 in. (86.4 cm) Overall width 34 in. (86.4 cm) Overall height 9.6 in. (24.4 cm) to carrier mount 10-1/2 in. (26.7 cm) at 3/4 in. height of cut 13-3/4 in. (34.9 cm) at 4 in. height of cut Roller footprint Front to back 29.5 in.

  • Page 6: Setup

    Setup Note: Determine the left and right sides of the machine from the normal operating position. Loose Parts Note: Use this chart as a checklist to ensure that all parts have been received. Without these parts, total setup cannot be completed.

  • Page 7: Adjusting The Height Of Cut

    Adjusting the Height of Cut Important This cutting deck often cuts approximately 1/4 inch lower than a reel cutting unit with the same bench setting. It may be necessary to have these rotary cutting deck’s bench set 1/4 inch above that of reels cutting in the same area.

  • Page 8: Installing The Mulching Baffle (Optional)

    Installing the Mulching Baffle (Optional) 1. Thoroughly clean debris from mounting holes on rear wall and left side wall of chamber. 2. Install mulching baffle in rear opening and secure with 5 flange head screws (Fig. 5). Figure 5 1. Mulching baffle 3.

  • Page 9: Operation

    Operation After Operating To ensure optimum performance, clean underside of mower housing. If residue is allowed to build up in mower Note: Determine the left and right sides of the machine housing, cutting performance will decrease. from the normal operating position. Operating Tips Blade Selection Standard Combination Sail...

  • Page 10: Maintenance

    The fittings are flush fittings and machine is operated under normal conditions, lubricate require a grease gun nozzle adapter, Toro Part No. blade spindle bearings (Fig. 6) with No. 2 general purpose 107–1998 which can be obtained from your Authorized lithium base grease or molybdenum base grease, after every Toro Distributor.

  • Page 11: Cutting Deck Service Latch (Groundsmaster 3500 Only)

    Cutting Deck Service Latch (Groundsmaster 3500–D only) When servicing cutting decks, use the service latch to prevent injury. 1. Center cutting deck sidewinder with the traction unit. 2. Raise cutting decks to transport position. 3. Set parking brake and turn off machine. Figure 9 4.

  • Page 12: Blade Plane

    Blade Plane Adjusting the Blade Plane The rotary deck comes from the factory preset at 2.00 inch Start with front adjustment (change one bracket at a time). height-of-cut and blade rake of 0.310 inch. The left-hand 1. Remove height-of-cut bracket, (front, left, or right) and right-hand heights are also preset to within ±0.030 inch from deck frame (Fig.

  • Page 13: Removing The Cutter Blade

    Always use genuine 1. Raise cutting deck to highest position, shut the engine Toro replacement blades to be sure of safety and optimum off, and engage the parking brake. Block cutting deck to performance.

  • Page 14: Blade Stopping Time

    Call your than .060 in. creates a side load on bearing and can lead to Toro Distributor for assistance in making this adjustment. premature bearing failure. 5. Verify that there is no more than a .060 in. gap between...

  • Page 16: The Toro General Commercial Products Warranty

    If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.

Table of Contents