Table of Contents
Advertisement
en Ventilation function "Crisp Finish"
11.3 Setting the microwave
Note:
Note the correct way to operate the microwave:
¡ → "Safety", Page 2
¡ → "Preventing material damage", Page 7
¡ → "Microwave output settings", Page 12
¡ → "Cookware and accessories with microwave",
Page 16
Press "Microwave".
1.
Or select the microwave directly using the
‒
ton.
2.
Press the required microwave output setting.
Press "Cooking time".
3.
A cooking time must always be set to operate the
microwave.
To change the preset cooking time, press the relev-
4.
ant time value, e.g. minute display "min" or second
display "s".
a The selected value is marked in blue.
Set the cooking time using the adjustment line or
5.
enter it directly via the number field
If required, use
to reset the setting value.
Press "Start" to start the operation.
6.
a The microwave starts and the cooking time counts
down. The display shows the performance reduction
for the maximum microwave output "Boost".
→ "Microwave output settings", Page 12
a When the time has elapsed, a signal sounds. A noti-
fication appears on the display confirming that the
operation has finished.
Once the cooking time has elapsed:
7.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
If you have switched off the drying function for the
8.
microwave in the basic settings and condensation
has formed in the cooking compartment, dry the
cooking compartment.
→ "Drying function", Page 30
Note: If you open the appliance door during operation,
the operation stops. If you close the appliance door,
you must continue the operation. If you have changed
the basic setting for this, make sure that the microwave
does not resume operation without food inside.
→ "Basic settings", Page 24
Ventilation function "Crisp Finish"
12 Ventilation function "Crisp Finish"
The ventilation function "Crisp Finish"
ture from the cooking compartment so that your meal
will be more crispy.
Hot steam that may escape when the appliance door is
opened is reduced.
12.1 Suitable types of heating with the
ventilation function
Only certain types of heating are suitable for the ventil-
ation function.
18
but-
.
to switch the ap-
extracts mois-
Changing the microwave output setting
You can change the microwave output at any time.
Press the microwave output setting.
1.
Change the microwave output setting.
2.
Press "Apply".
3.
Changing the cooking time
You can change the cooking time at any time.
Press the cooking time.
1.
Change the cooking time using the adjustment line
2.
or enter it directly via the number field
Press "Apply".
3.
11.4 Setting added microwave
Note:
Note the correct way to operate the microwave:
¡ → "Safety", Page 2
¡ → "Preventing material damage", Page 7
¡ → "Microwave output settings", Page 12
¡ → "Cookware and accessories with microwave",
Page 16
Requirement: Observe the information about the re-
spective operating mode.
→ "Setting options with the microwave", Page 17
Press the operating mode that you require.
1.
Implement the settings for the operating mode, e.g.
2.
type of heating and temperature.
Press "Added microwave"
3.
Press the required microwave output setting.
4.
Press "Cooking time" and set the cooking time.
5.
Use "Start" to start the operation.
6.
a The appliance starts to heat and the time counts
down.
a Once the cooking time has elapsed, a signal tone
sounds. A notification appears on the display con-
firming that the operation has finished.
Once the cooking time has elapsed:
7.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Changing added microwave
You can change or deactivate the added microwave at
any time.
Press the microwave output setting.
1.
2.
Change or deactivate the microwave output setting.
Press "Apply".
3.
You can use the ventilation function for the following
types of heating:
¡ 4D hot air
¡ Top/bottom heating
¡ Intensive heat
¡ Pizza setting
¡ Circulated air grilling
.
.
to switch the ap-
Advertisement
Table of Contents
