Installation Instructions; Requirements; Tools And Parts - KitchenAid KSDB900ESS Owner's Manual

7. If any soils remain, remove them with a non-scratch scrubbing
sponge or plastic scraper. Additional Clean cycles may be run
to help remove the stubborn soils.
IMPORTANT: Do not use oven cleaners. The use of
chemicals, including commercial oven cleaners or metal
scouring pads, may cause permanent damage to the
porcelain surface of the oven interior.
NOTES:
� The range should be level to ensure that the entire surface
of the bottom of the oven cavity is covered by water at the
beginning of the Clean cycle.
� For best results, use distilled or filtered water. Tap water
may leave mineral deposits on the oven bottom.
� Before removing the residual water and loosened soils at
the end of the Clean cycle, insert a cloth or paper towel
between the lower edge of the oven door and the front
frame to keep water from spilling onto the front of the
range and the floor.
� Soil baked on through several cooking cycles will be more
difficult to remove with the Clean cycle.
� Nonabrasive scrub sponges or eraser style cleaning pads
(without cleaners) can be effective for cleaning the oven
cavity walls, oven door and oven bottom for difficult soils.
For best results, moisten the pads and sponges before
use.
� Run an additional Clean cycle for stubborn soils.
� Affresh
® Kitchen Appliance Cleaner and affresh
Cleaner may be used to clean the oven bottom, walls, and
door when the oven has finished the cycle and returned to
room temperature. If affresh
is recommended to wipe out the cavity with distilled water
as well. Refer to the Quick Start Guide for ordering
information.
� Additional AquaLift ®
obtained by ordering Part Number W10423113RP. Refer to
the Quick Start Guide for ordering information.
� For assistance with AquaLift
1-877-258-0808 in the U.S.A. or 1-800-807-6777 in
Canada, or visit our website at
http://whirlpoolcorp.com/aqualift.
® Cooktop Cleaner is used, it
Technology Cleaning Kits may be
® Technology, call

INSTALLATION INSTRUCTIONS

REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
� Tape measure
� Phillips screwdriver
� Flat-blade screwdriver
� 1/8" (3.2 mm) flat-blade
screwdriver
� Hand or electric drill
� Level
� Wrench or pliers
� Pipe wrench
� 15/16" (2.4 cm) combination
wrench
� 1/8" (3.2 mm) drill bit
� Torque Wrench
� Tin snips or large wire
cutters (for cutting
® Cooktop
ground-link strap if
necessary)
Parts supplied
Check that all parts are included.
� Propane/Natural Gas Conversion Kit
� 10-32 hex nuts (attached to terminal block) (3)
� Direct wire lugs (3)
� #10 x 1
� Anti-tip bracket (inside oven cavity)
Anti-tip bracket must be securely mounted to the back wall or
floor. Thickness of flooring may require longer screws to
anchor bracket to subfloor. Longer screws are available from
your local hardware store.
Parts Needed
If using a power supply cord kit:
� A UL listed power supply cord kit marked for use with ranges.
The cord should be rated at 250 V minimum, 40 A or 50 A that
is marked for use with nominal 1
connection opening and must end in ring terminals or
open-end spade terminals with upturned ends.
� A UL listed strain relief.
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See the appropriate "Electrical
Requirements" and "Gas Supply Requirements" sections.
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
NOTE: Be sure to purchase only Whirlpool factory-certified parts
and accessories for your appliance. Your installation may require
additional parts. To order, refer to the contact information
referenced in your Quick Start Guide.
� Marker or pencil
� Pipe-joint compound
resistant to propane gas
� 3/16" (4.8 mm)
carbide-tipped masonry drill
bit (for concrete/ceramic
floors)
� Noncorrosive leak-detection
solution
For Propane/Natural Gas
Conversions
� 1/2" (1.3 cm) combination
wrench
� 1/4" (6 mm) nut driver
� 9/32" (7.0 mm) nut driver
� Masking tape
5 ⁄ " (4.1 cm) screws (for mounting anti-tip bracket) (2)
8
3 ⁄
8
" (3.5 cm) diameter
7