English (Original Instructions) - Stanley FATMAX V20 SFMCN618 Manual

ENGLISH
f. Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or temperature
above 130 °C may cause explosion.
g. Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage the
battery and increase the risk of fire.
6. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
b. Never service damaged BATTERY packs. Service of
BATTERY packs should only be performed by the
manufacturer or authorized service providers
Additional power tool safety warnings
Use auxiliary handles supplied with the tool.
u
Loss of control can cause personal injury.
Hold power tool by insulated gripping surfaces when
u
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Hold power tool by insulated gripping surfaces, when
u
performing an operation where the fastener may
contact hidden wiring. Fasteners contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
Before drilling into walls, floors or ceilings, check for the
u
location of wiring and pipes.
Avoid touching the tip of a drill bit just after drilling, as it
u
may be hot.
The intended use is described in this instruction manual.
u
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Safety of others
Never allow children, persons with reduced physical,
u
sensory or mental capabilities or lack of experience and
knowledge or people unfamiliar with these instructions to
use the machine,
local regulations may restrict the age of the operator.
u
Never operate the machine while people, especially
u
children, or pets are nearby.
8
(Original instructions)
Additional Safety Instructions for Cordless Nailers
Always wear safety glasses.
u
Always wear ear protection.
u
Only use fasteners of the type specified in the manual.
u
Do not use any stands for mounting the tool to a
u
support.
Do not disassemble or block any parts of the fastener
u
driving tool such as the contact trip.
Prior to each operation check that the safety and
u
triggering mechanism is functioning properly and that
all nuts and bolts are tight.
Do not use the tool as a hammer.
u
Do not use the tool on a ladder.
u
Never point any operational fastener driving tool at
u
yourself or at any other person.
While working, hold the tool in such a way that no
u
injuries can be caused to the head or to the body in
the event of a possible recoil due to a disruption in
the energy supply or hard areas within the work piece.
Never actuate the fastener driving tool into free space.
u
In the work area, carry the tool at the workplace using
u
only one handle, and never with the trigger actuated.
Consider the conditions in the work area Fasteners
u
can penetrate thin work pieces or slip off corners and
edges of the work piece, and thus put people at risk.
Do not drive fasteners close to the edge of the work
u
piece.
Do not drive fasteners on top of other fasteners.
u
Always assume that the tool contains fasteners.
u
Careless handling of the nailer can result in unexpected
firing of fasteners and personal injury.
Do not point the tool towards yourself or anyone
u
nearby. Unexpected triggering will discharge the fastener
causing injury.
Do not actuate the tool unless it is placed firmly
u
against the workpiece. If the tool is not in contact, the
fastener may be deflected away from your target.
Disconnect the tool from the power source when the
u
fastener jams in the tool. While removing a jammed
fastener, the nailer may be accidentally activated if it is
plugged in.
Do not use this tool for fastening electrical cables.
u
It is not designed for electric cable installation and may
damage the insulation of electric cables thereby causing
electric shock or fire hazards.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings.
These risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include: