Troubleshooting; Connection To The Mains Supply - Breville BRITA HotCup Manual

TROUBLESHOOTING

Problem Possible Cause
The start switch will not stay in Your HotCup
the on position. has not reset itself after the
boiling cycle.
The water tank does not • Your HotCup
illuminate and your HotCup dispenser is not plugged in.
™
water dispenser does not
• Your HotCup
dispense boiling water.
dispenser is not positioned
correctly on its power base.
• The fuse has blown.
• Your HotCup
dispenser has boiled dry.
Your HotCup ™ water dispenser • Your HotCup
does not dispense a full cup dispenser has excessive
of water. scale.
• The dispensing control may
be set too low.
Your HotCup water dispenser • There is not enough water
™
produces excess steam but in your HotCup
does not dispense boiling dispenser.
water.
• Your HotCup
dispenser has excessive
scale.
Your HotCup ™ water dispenser This is the sound of the
makes a noise and there is a internal valve operating after
'clunk' sound after water has the boil cycle finishes.
been dispensed.
Water drips from the There is a residual amount of
dispensing nozzle after the boil water left inside your HotCup
cycle has finished. water dispenser after the boil
cycle.
Steam comes out from behind Steam is being vented in a
the start button and behind the controlled manner through
dispensing nozzle. designed vents.
The water reservoir is getting Hot water is being returned to
hot. the water reservoir.
Your HotCup water dispenser Your HotCup
™
immediately turns iteslf on is already switched on.
when it is placed on the power
base.
14
VKJ367_22EM1 (UK).indd 14-15 VKJ367_22EM1 (UK).indd 14-15
Solution
water dispenser Your HotCup water dispenser
™ ™
is still too hot after the last boil
cycle. Wait a few seconds for
it to cool slightly before trying
again.
™ water • Check your HotCup ™ water
dispenser is plugged in and
switched on at the supply
water
™
socket.
• Check that the dispensing
nozzle is positioned
centrally over the drip tray.
water
™
• Check the fuse in the plug.
• Allow your HotCup ™ water
dispenser to cool down
completely then refill it with
water.
™ water • Descale your HotCup ™
water dispenser.
• Adjust the dispensing
control.
• Fill with water up to the
water MAX marking then restart
™
the boil cycle.
water • Descale your HotCup
™ ™
water dispenser.
This is normal operation.
This is normal operation.
™
This is normal operation.
This is normal operation.
water dispenser Press the stop button.
™

CONNECTION TO THE MAINS SUPPLY

If the plug is not suitable for the socket outlets in your home, it can be removed and
replaced by a plug of the correct type.
If the fuse in a moulded plug needs to be changed, the fuse cover must be refitted. The
appliance must not be used without the fuse cover fitted.
If the plug is unsuitable, it should be dismantled and removed from the supply cord and
an appropriate plug fitted as detailed. If you remove the plug it must not be connected to
a 13 amp socket and the plug must be disposed of immediately.
If the terminals in the plug are not marked or if you are unsure about the installation of the
plug please contact a qualified electrician.
Plug should be ASTA approved to BS1363
Fuse should be ASTA approved to BS1362
Green/Yellow
(Earth)
Blue
(Neutral)
Ensure that the outer sheath of
the cable is firmly held by the cord grip
TURN ON YOUR CREATIVITY
™
Let the Breville team help you turn on your creativity with a gateway to a world of food
®
and drinks without limits. You don't have to travel far—just to your computer, tablet or
mobile—where you will discover our FREE website with top tips and recipes to inspire
your imagination. Join us now at: www.turnonyourcreativity.com
13A Fuse
Brown
(Live)
®
15
3/3/2022 2:44:43 PM 3/3/2022 2:44:43 PM