Table of Contents
Advertisement
•
F80-Q7, F80-4K7:
-
The projector is Class 1 laser product that conforms with IEC EN 60825-1:2014. The projector
conforms with IEC 60825–1:2007, and with performance standards for laser products under 21 CFR
1040, except with respect to those characteristics authorized by Variance Number 2017-V-4837
effective September 13, 2017 Do not stare into Beam.
-
This projector is Risk Group 2 (RG2) according to IEC EN 62471-5. This projector may become Risk
Group 3 (RG3) when an interchangeable lens with throw ratio greater than 3.5 is installed. Refer to the
manual for the lens list and throw ratio before operation. Such combination of projector and lens are
intended for professional use only, and are not intended for consumer use. Safety considerations for
RG3 projectors are discussed in section
-
This projector has one or several built-in Class 4 laser clusters. Disassembly or modification is very
dangerous and should never be attempted.
Users definition
Throughout this manual, the term SERVICE PERSONNEL refers to Barco authorized persons having
appropriate technical training and experience necessary to be knowledgeable of potential hazards to which
they are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY
and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize the potential risk
to themselves or other persons. Only Barco authorized SERVICE PERSONNEL, knowledgeable of such risks,
are allowed to perform service functions inside the product enclosure. The term USER and OPERATOR refers
to any person other than SERVICE PERSONNEL. When installing an interchangeable lens with a throw ratio
that make the projector become RG3, refer to chapter
projector and lens are intended for professional use only, and are not intended for consumer use.
FOR PROFESSIONAL USE ONLY means installation can only be carried out by Barco AUTHORIZED
PERSONNEL familiar with potential hazards associated with high intensity light beams.
1.2 Important safety instructions
To prevent the risk of electrical shock
•
This product should be operated from a mono phase AC power source.
•
This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the
supplied power cables are the correct one, consult your dealer. If you are unable to insert the plug into the
outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-
type plug. Never use 2-prong power cords, as this is dangerous and could lead to electrical shock.
•
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the
cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself.
•
Use only the power cord supplied with your device. While appearing to be similar, other power cords have
not been safety tested at the factory and may not be used to power the device. For a replacement power
cord, contact your dealer.
•
Do not operate the projector with a damaged cord. Replace the cord.
•
Do not operate the projector if the projector has been dropped or damaged - until it has been examined
and approved for operation by qualified service personnel.
•
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
•
If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should
be used. A cord rated for less amperage than the projector may overheat.
•
Never push objects of any kind into this product through cabinet slots as they may touch dangerous
voltage points or short out parts that could result in a risk of fire or electrical shock.
•
Make sure that no objects enter into the vents and openings of the set.
•
Do not expose this projector to rain or moisture.
•
The projector is designed for indoor use only. Never operate the unit outdoors.
•
Do not immerse or expose this projector in water or other liquids.
•
Do not spill liquid of any kind on this projector.
•
Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified
service personnel before resuming operations.
•
Do not disassemble this projector, always take it to qualified service personnel when service or repair work
is required.
•
Do not use an accessory attachment which is not recommended by the manufacturer.
"Risk Group 3 Safety", page
"Risk Group 3 Safety", page
Safety
17.
17. Such combination of
R5906852 /09
F80
11
Advertisement
Table of Contents
