Related Manuals for Planet XGS-6320-8UP4X
Summary of Contents for Planet XGS-6320-8UP4X
- Page 1 L3 Multi-port 10Gigabit Managed Ethernet Switch XGS-6320-8X8TR XGS-6320-12X4TR XGS-6320-8UP4X Quick Installation Guide...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents ................. 3 2. Requirements ..................4 3. Terminal Setup ..................5 3.1 Logging on to the Console .............. 6 3.2 Configuring IP Address ..............7 3.3 Storing Current Switch Configuration ..........9 4. Starting Web Management ..............10 4.1 Logging in to the Managed Switch ..........11 4.2 Saving Configuration .............. -
Page 3: Package Contents
1. Package Contents Thank you for purchasing PLANET Multi-port 10Gigabit Managed Ethernet Switch, XGS-6320-8X8TR/XGS-6320-12X4TR/XGS-6320-8UP4X. The descriptions of these models are shown below: Layer 3 8-Port 10GBASE-X SFP+ + 8-Port 10GBASE-T XGS-6320-8X8TR Managed Ethernet Switch Layer 3 12-Port 10GBASE-X SFP+ + 4-Port 10GBASE-T XGS-6320-12X4TR Managed Ethernet Switch Layer 3 8-Port 10GBASE-T 802.3bt PoE + 4-Port XGS-6320-8UP4X 10GBASE-X SFP+ Managed Ethernet Switch “Managed Switch” is used as an alternative name in this Quick Installation Guide. Open the box of the Managed Switch and carefully unpack it. The box should... -
Page 4: Requirements
2. Requirements z Workstations running Windows 7/8/10/11, MAC OS 11 or later, Linux, UNIX, or other platforms that are compatible with TCP/IP protocols. z Workstations are installed with Ethernet NIC (Network Interface Card) z Serial Port Connection (Terminal) The above Workstations come with COM Port (DB9) or USB-to-RS232 converter. The above Workstations have been installed with terminal emulator, such as Tera Term or PuTTY. -
Page 5: Terminal Setup
3. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to RJ45 type of serial port of the Managed Switch. PC / Workstation with Terminal Emulation Software Managed Switch RS232 to RJ45 Cable Serial Port RJ45 Console Port Figure 3-1: Managed Switch Console Connectivity A terminal program is required to make the software connection to the Managed Switch. -
Page 6: Logging On To The Console
3.1 Logging on to the Console Once the terminal is connected to the device, power on the Managed Switch, and the terminal will display “running testing procedures”. Subsequently, a prompt will request the entry of your username and password. The factory default user name and password are shown as follows and you can refer to Figure 3-3 for the login screen. -
Page 7: Configuring Ip Address
3.2 Configuring IP Address The Managed Switch is shipped with default IP address shown below. IP Address: 192.168.0.100 Subnet Mask: 255.255.255.0 To check the current IP address or modify a new IP address for the Switch, please use the procedures as follows: Show the current IP Address 1. At the “#” prompt, enter “show ip interface brief”. 2. The screen displays the current IP address as shown in Figure 3-4. Figure 3-4: IP Information Screen... - Page 8 Configuring IP Address 3. At the “#” prompt, enter the following command and press <Enter> as shown in Figure 3-5. XGS-6320-8X8TR # configure terminal XGS-6320-8X8TR (config)# interface vlan 1 XGS-6320-8X8TR (config-if-vlan)# ip address 192.168.1.100 255.255.255.0 The previous command would apply the following settings for the Managed Switch. IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0 Figure 3-5: Configuring IP Address Screen 4. Repeat step 1 to check if the IP address has changed.
-
Page 9: Storing Current Switch Configuration
3.3 Storing Current Switch Configuration In the Managed Switch, the running configuration sequence running-config can be saved from the RAM to FLASH by “copy” command, so that the running configuration sequence becomes the start-up configuration file, which is called configuration save. At the “#” prompt, enter the following command and press <Enter>. # copy running-config startup-config Figure 3-6: Saving Current Configuration Command Screen If you are not familiar with the console command or the related parameter, enter “help”... -
Page 10: Starting Web Management
4. Starting Web Management The following shows how to start up the Web Management of the Managed Switch. Note the Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address. -
Page 11: Logging In To The Managed Switch
4.1 Logging in to the Managed Switch 1. Use Chrome, Edge or Firefox Web browser and enter IP address https://192.168.0.100 (the factory default IP address or the one that you have just changed in console) to access the Web interface. 2. When the following dialog box appears, please enter the default user name and password “admin” (or the password you have changed via console). The login screen in Figure 4-2 appears. - Page 12 3. After entering the password, the main screen appears as Figure 4-3 shows. Figure 4-3: Web Main Screen of Managed Switch The Switch Menu on the top of the Web page lets you access all the commands and statistics the Managed Switch provides. The Switch Menu always contains one or more buttons, such as “System”, “Switching”, “Routing”...
- Page 13 Figure 4-6: Switch Menu – Security, Ring and Maintenance Figure 4-7: Switch Menu – PoE (only applies to XGS-6320-8UP4X) If you are not familiar with Switch functions or the related parameter, press “Help icon” anytime on the Web page to get the help description.
-
Page 14: Saving Configuration
4.2. Saving Configuration To save all applied changes and set the current configuration as a startup configuration on the Web user interface, the startup-configuration file will be loaded automatically across a system reboot. 1. Click the Save icon on the top Switch Menu bar. Figure 4-8: Save Config -- Hot key 2. -
Page 15: Recovering To Default Configuration
5. Recovering to Default Configuration IP address has been changed or admin password has been forgotten – To reset the IP address to the default IP address “192.168.0.100” or reset the login password to default value, press the hardware-based reset button on the front panel for about 10 seconds. After the device is rebooted, you can log in the management Web interface within the same subnet of 192.168.0.xx. -
Page 16: Customer Support
6. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQs resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team.