Garmin GPSMAP 1000 Owner's Manual page 46

uses that channel for subsequent calls until you call using
another channel.
1 Select NAV INFO > DSC List.
2
Select a vessel or a station to call.
3 Select Review > Call with Radio > Channel.
4
Select an available channel.
Making an Individual Routine Call
NOTE: When initiating a call from the chartplotter, if the radio
does not have an MMSI number programmed, the radio will not
receive call information.
1
Select NAV INFO > DSC List.
2
Select a vessel or a station to call.
3
Select Review > Call with Radio.
4
If necessary, select Channel, and select a new channel.
5
Select Send.
The chartplotter sends information about the call to the radio.
6 On your Garmin VHF radio, complete the call.
Making an Individual Routine Call to an AIS Target
1
From a chart or 3D chart view, select an AIS target.
2
Select AIS Vessel > Call with Radio.
3
If necessary, select Channel, and select a new channel.
4
Select Send.
The chartplotter sends information about the call to the radio.
5
On your Garmin VHF radio, complete the call.
Gauges and Graphs
The gauges and graphs provide various information about the
engine and environment. To view the information, a compatible
transducer or sensor must be connected to the network.
Viewing the Gauges
1 Select A/V, Gauges, Controls.
2
Select a gauge.
3 Select or to view a different gauge page.
Changing the Data Shown in a Gauge
1 From a gauges screen, hold a gauge.
2
Select Replace Data.
3 Select a data type.
4
Select the data to display.
Customizing the Gauges
You can change the layout of the gauge pages, how the gauges
pages are displayed, and the data in each gauge.
1
Open a gauge page.
2 Select MENU > Edit Gauge Pages.
3
Select an option:
• To change the data shown in a gauge, select the gauge.
• To change the layout of the gauges on the page, select
Change Layout.
• To add a page to this set of gauge pages, select Add
Page.
• To change the order of this page in the set of gauge
pages, select Move Page Left or Move Page Right.
• To restore this page to the original view, select Restore
Default View.
38
Customizing Engine Gauge and Fuel Gauge Limits
You can configure the upper and lower limits and the range of
desired standard operation of a gauge.
NOTE: Not all options are available for all gauges.
1
From an applicable gauges screen, select MENU >
Installation > Set Gauge Limits.
2
Select a gauge to customize.
3 Select an option:
• To set the minimum value of the standard operating
range, select Rated Min..
• To set the maximum value of the standard operating
range, select Rated Max..
• To set the lower limit of the gauge lower than the rated
minimum, select Scale Min..
• To set the upper limit of the gauge higher than the rated
maximum, select Scale Max..
4
Select the limit value.
5
Repeat steps 4 and 5 to set additional gauge limits.
Viewing Engine and Fuel Gauges
Before you can view engine and fuel gauges, you must be
connected to a NMEA 2000 network capable of sensing engine
and fuel data. See the installation instructions for details.
Select A/V, Gauges, Controls > Engines.
Selecting the Number of Engines Shown in Gauges
You can show information for up to four engines.
1
From the engine gauges screen, select MENU > Installation
> Engine Selection > Num. Engines.
2
Select an option:
• Select the number of engines.
• Select Auto Configure to automatically detect the number
of engines.
Customizing the Engines Shown in Gauges
Before you can customize how the engines are shown in the
gauges, you must manually select the number of engines
(Selecting the Number of Engines Shown in Gauges, page
1
From the engine gauges screen, select MENU > Installation
> Engine Selection > Num. Engines.
2
Select First Engine.
3
Select the engine to display in the first gauge.
4
Repeat for the remaining engine bars.
Enabling Status Alarms for Engine Gauges
You can enable the chartplotter to display engine status alarms.
From the engine gauges screen, select MENU > Installation
> Status Alarms > On.
When an engine alarms is triggered, a gauge status alarm
message appears and the gauge may become red depending
on the type of alarm.
Enabling Some Engine Gauge Status Alarms
1
From the engine gauges screen, select MENU > Installation
> Status Alarms > Custom.
2
Select one or more engine gauge alarms to turn on or off.
Yamaha Engine Gauges
®
Select A/V, Gauges, Controls > YAMAHA to view the Yamaha
engine gauges. This screen varies based on the engine network
and throttle controller.
38).
Gauges and Graphs