1. Manuals
  2. Brands
  3. Hitachi Manuals
  4. Nail Gun
  5. NT 32AE2
  6. Instruction and safety manual

Hitachi NT 32AE2 Instruction And Safety Manual

Brad nailer
Hide thumbs Also See for NT 32AE2:
Table of Contents

Advertisement

Quick Links

Download this manual
Instruction and safety manual
Model
NT 50AE2
Improper use of this Nailer can result in death or serious injury!
This Manual contains important information about product safety.
Read and understand this Manual before operating the Nailer.
Never allow anyone who has not reviewed this manual.
•
NT 32AE2
DANGER
Brad Nailer

Advertisement

Table of Contents
loading

Related Manuals for Hitachi NT 32AE2

Summary of Contents for Hitachi NT 32AE2

  • Page 1 Instruction and safety manual Model Brad Nailer NT 50AE2 • NT 32AE2 DANGER Improper use of this Nailer can result in death or serious injury! This Manual contains important information about product safety. Read and understand this Manual before operating the Nailer.

  • Page 2: Table Of Contents

    DEFINITIONS OF SIGNAL WORDS ......3 AIR SUPPLY ............11 EXPLANATION OF THE NAILING ACTION LUBRICATION ............. 12 OF THE HITACHI NAILER ........3 COLD WEATHER CARE ........13 TESTING THE NAILER ........13 SAFETY ADJUSTING AIR PRESSURE ......16 IMPORTANT SAFETY INSTRUCTIONS LOADING NAILS ..........

  • Page 3: Important Safety Information

    NOTE emphasizes essential information. EXPLANATION OF THE NAILING ACTION OF THE HITACHI NAILER SINGLE ACTUATION MECHANISM (SINGLE SEQUENTIAL ACTUATION MECHANISM): First, press the push lever against the wood; next, pull the trigger to drive the fastener.

  • Page 4: Safety

    English SAFETY IMPORTANT SAFETY INSTRUCTIONS FOR USING NAILERS READ ALL INSTRUCTIONS DANGER 1. OPERATORS AND OTHERS IN WORK AREA MUST WEAR SAFETY GLASSES WITH SIDE SHIELDS. When operating the Nailer, always wear safety glasses with side shields, and make sure others in work area wear safety glasses, too. Safety glasses must conform to the requirements of American National Standards Institute, ANSI Z87.1 and provide protection against flying particles both from the front and side.
  • Page 5 19. BEFORE STARTING WORK, CHECK THE FASTENING OPERATION SWITCHING DEVICE. This Hitachi nailer includes a fastening operation switching device. Before starting work, check the setting of the operation switching device. If the switching device is not set properly, the nailer will not operate correctly.
  • Page 6 26. NEVER USE NAILER WHICH IS DEFECTIVE OR OPERATING ABNORMALLY. If the Nailer appears to be operating unusually, making strange noises, or otherwise appears defective, stop using it immediately and arrange for repairs by a Hitachi authorized service center. 27. DO NOT DISCONNECT AIR HOSE FROM NAILER WITH FINGER ON TRIGGER.

  • Page 7: Employer's Responsibilities

    Unauthorized parts, accessories, or fasteners may void your warranty and can lead to malfunction and resulting injuries. Only service personnel trained by Hitachi, distributor or employer shall repair the Nailer. 35. NEVER MODIFY OR ALTER A NAILER. Doing so may cause it to malfunction and personal injuries may result.

  • Page 8: Operation

    English OPERATION NOTE: The information contained in this Manual is designed to assist you in the safe operation of the Nailer. Some illustrations in this Manual may show details or attachments that differ from those on your own Nailer. NAME OF PARTS Nailing operation switching device Enlarged view of the valve part Switching...

  • Page 9: Specifications

    (.73 ltr/cycle at 7 kgf/cm NAIL SELECTION WARNING ● Be sure to use only the genuine HITACHI nails for the NT65M2. The use of any other nails can result in tool malfunction and/or nail breakdown, leading to serious injuries. Only nails shown in the Table below can be driven with this Nailer.

  • Page 10: Accessories

    4 oz. (120 cc) oil feeder (Code No.874042) 1 quart (1 ltr) can (Code No.876212) NOTE: Accessories are subject to change without any obligation on the part of HITACHI. APPLICATIONS Cabinet and picture frame assembly, furniture trim. On-site and mobile home trim and molding.

  • Page 11: Air Supply

    Inspect the regulator before operation to be sure it operates properly. Lubricator The lubricator supplies an oil mist to the Nailer. Inspect the lubricator before operation to be sure the supply of lubricant is adequate. Use Hitachi pneumatic tool lubricant. Regulator Nailer side Compressor side Filter...

  • Page 12: Lubrication

    Filter-regulator-lubricator units should always be used. Keep the lubricator filled with Hitachi pneumatic tool lubricant. If a lubricator is not available, supply 5 – 10 drops of Hitachi pneumatic tool lubricant into the air plug on the Nailer twice a day.

  • Page 13: Cold Weather Care

    Before actually beginning the nailing work, test the Nailer by using the check list below. Conduct the tests in the following order. If abnormal operation occurs, stop using the Nailer and contact a Hitachi authorized service center immediately. (1) DISCONNECT AIR HOSE FROM NAILER.
  • Page 14 English THE PUSH LEVER AND TRIGGER MUST MOVE SMOOTHLY. Trigger Do not connect Push lever air hose (2) Adjust the air pressure to 70 psi (4.9 bar 5 kgf/cm Connect the air hose. Do not load any nails in the Nailer. Set the switching device to the upward position (SINGLE ACTUATION MECHANISM).
  • Page 15 English (4) Separate the push lever from the wood. Next, point the nailer downward, pull the trigger and then wait in that position for 5 seconds or longer. THE NAILER MUST NOT OPERATE. Pull trigger (5) 1 Without touching the trigger, depress the push lever against the workpiece. Pull the trigger.

  • Page 16: Adjusting Air Pressure

    English ADJUSTING AIR PRESSURE WARNING ● Do not exceed 120 psi (8.3 bar 8.5 kgf/cm Adjust the air pressure at recommended operating pressure 70 – 120 psi (4.9 – 8.3 bar 5 – 8.5 kgf/cm ) according to the length of nails and the hardness of workpiece. The correct air pressure is the lowest pressure which will do the job.

  • Page 17: Nailer Operation

    English NOTE: ● The nails shown in page 9 can be loaded Magazine onto the side guide groove of the magazine without any adjustment. Always keep the points of nails in contact with Groove. Side guide groove Nail Groove (3) Slide the nail strip into the blade guide. Nail strip Blade guide (4) Confirm that nail strip is placed with side...
  • Page 18 5) moving it to another location; and 6) handing it to another person. This Hitachi nailer is equipped with a nailer operation switching device. Use SINGLE ACTUATION MECHANISM or CONTACT ACTUATION MECHANISM in accordance with the work to be performed.

  • Page 19: Methods Of Operation

    WARNING ● Please note that the SINGLE ACTUATION MECHANISM of this Hitachi nailer will drive a nail each time the push lever is pressed against the wood as long as the trigger is pressed. ● For intermittent operation, set the switching device to the upward position completely.
  • Page 20 ● Keep hands and body away from the discharge area. This Hitachi nailer may bounce from the recoil of driving a nail and unwanted subsequent nail may be driven, possibly causing injury.

  • Page 21: Adjusting The Nailing Depth

    1) disconnect air hose from the Nailer; 2) remove all nails from the Nailer; 3) supply 5 – 10 drops of Hitachi pneumatic tool lubricant into the air plug on the Nailer; 4) open the petcock on the air compressor tank to drain any moisture.

  • Page 22: Changing The Exhaust Direction

    English CHANGING THE EXHAUST DIRECTION WARNING ● When changing the exhaust direction, be sure to remove your finger from the trigger and disconnect the air hose from the nailer. The direction of the exhaust vent can be changed by turning the top cover. Top cover Exhaust vent USING THE NOSE CAP...

  • Page 23: Maintenance

    5 Close guide plate and latch. 6 In case of frequent jam, contact a Hitachi authorized service center. 2. Storing When not in use for an extended period, apply a thin coat of the lubricant to the steel parts to avoid rust.
  • Page 24 Repair, modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance.

  • Page 25: Service And Repairs

    ● Use only parts supplied or recommended by Hitachi for repair. All quality Nailers will eventually require servicing or replacement of parts because of wear from normal use. NOTE: Specifications are subject to change without any obligation on the part of HITACHI. Maintenance chart ACTION Drain air line filter daily.
  • Page 26 English Operator troubleshooting Most minor problems can be resolved quickly and easily using the table below. If problems persist, contact a Hitachi authorized service center for assistance. PROBLEM CHECK METHOD CORRECTION Nailer operates, Check for a jam. Clear a jam page 23.
  • Page 27 NT50AE2...
  • Page 28 CASE CAP (A) HEX. SOCKET HD. BOLT M5 × 16 AIR PLUG NPT 1/4 STEEL BALL D3.97 SPRING (C) CHANGE KNOB (C) HITACHI LABEL PROTECTOR TRIGGER (C) ASS'Y PUSHING LEVER GUIDE PUSHING SPRING (A) PUSHING LEVER (C) ADJUSTER PUSHING LEVER (B)
  • Page 29 NT32AE2...
  • Page 30 CASE CAP (A) HEX. SOCKET HD. BOLT M5 × 16 AIR PLUG NPT 1/4 STEEL BALL D3.97 SPRING (C) CHANGE KNOB (C) HITACHI LABEL PROTECTOR TRIGGER (C) ASS'Y PUSHING LEVER GUIDE PUSHING SPRING (A) PUSHING LEVER (C) ADJUSTER PUSHING LEVER (B)

This manual is also suitable for:

Nt 50ae2

Table of Contents