Table of Contents
Advertisement
ONE-KEY™
To learn more about the ONE-KEY™ functionality
for this tool, go to milwaukeetool.com/One-Key. To
download the ONE-KEY™ app, visit the App Store or
Google Play from your smart device.
ONE-KEY™ Indicator
Solid Blue
Wireless mode is active and ready
to
ONE-KEY™ app.
Blinking Blue
Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red
Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
OPERATION
To reduce the risk of injury,
WARNING
always
protection
marked
AS/NZS 1337.1.
When working in dusty situations, wear
appropriate respiratory protection or use a
suitable dust extraction solution.
Selecting Hammer, Drill or Drive Action
1. To use the hammer-drilling
mode, rotate the torque selector
collar until the hammer symbol
appears in line with the ar-
row. Apply pressure to the bit to
engage the hammering mecha-
nism.
When using carbide
NOTICE
water to settle dust. Do not attempt
to drill through steel reinforcing rods. This will
damage the carbide bits.
2. To use the drilling only mode,
rotate the torque selector collar
until the drill symbol
in line with the arrow.
3. To use the driving screws
mode, rotate the torque selector
collar until the desired clutch set-
ting appears in line with the
arrow.
The adjustable clutch, when
properly adjusted, will slip at a
preset torque to prevent driving the screw too
deep into different materials and to prevent
damage to the screw or tool.
The
torque
specifications
approximate values obtained with a fully charged
battery pack.
TORQUE SPECIFICATIONS
Clutch
Nm
Setting
1-4
1.7 - 3
Small screws in softwood.
5-8
3.5 - 4.8
9-12
5.3 - 6.8
Medium screws in softwood
7.1 - 8.5
13-16
or small screws in hardwood.
NOTE: Because the settings shown in the table are
only a guide, use a piece of scrap material to test
the different clutch settings before driving screws
into the workpiece.
be
configured
via
wear
proper
to
comply
bits, do not use
appears
shown
here
Applications
The tool has three modes that come with default
speed settings as shown below.
settings can be changed via the ONEKEY App on
your smart device. The speed setting for each mode
will be dependent on the speed setting selected via
the Speed Selector Switch with 500 RPM being the
max speed for LOW and 2100 RPM the max for
HIGH.
Mode
the
LOW
HIGH
Selector
button
eye
with
AutoSTOP™ Indicator
Allow the tool to come to a complete stop before
changing modes. Press the selector button
cycle between the settings. When the tool is con-
nected to the ONE-KEY App™, the indicator will blink.
Select wireless
and AutoSTOP™
KEY™ App on your smart device.
The speed selector is on top of the motor housing.
Allow the tool to come to a complete stop before
changing speeds. See "Applications" for recom-
mended speeds under various conditions.
1.
For Low speed, push the speed selector to display
"1".
2.
For High speed, push the speed selector to display
"2".
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
For forward (clockwise) rotation, push in the control
switch
from the right side of the tool. Check the
direction of rotation before use.
For reverse (anticlockwise) rotation, push in the
control switch
are
direction of rotation before use.
To lock the trigger, push the control switch to the
centre position. The trigger will not work while the
control switch is in the centre locked position.
Always lock the trigger or remove the battery pack
before
performing
accessories, storing the tool and any time the tool is
not in use.
5
1
2
0-200
0-300
0-500
0-1200
Mode Selector
ONE-KEY™ Indicator
to change the default RPM, BPM,
control settings via the ONE-
Selecting Speed
from the left side of the tool. Check
maintenance,
These speed
3
0-500
0-2100
Modes
1, 2, 3
to
changing
Advertisement
Table of Contents
