INTEX AP619RL - Built-in Fast-Fill Water Pump With Remote Control Manual

Also See for AP619RL:

Owner's manual (2 pages)

Table of Contents

Contents

1 INSTRUCTIONS
2 PARTS REFERENCE
3 INFLATION
4 DEFLATION
5 INFLATION OPTION
6 STORAGE
7 Documents / Resources
- 7.1 Download manual

INTEX AP619RL - Built-in Fast-Fill Water Pump With Remote Control Manual

INSTRUCTIONS

General

This appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
No air pump maintenance is required.
For cleaning use only mild soapy solution. Do not use any chemicals.
In case of repairs, use only common PVC repair glue and patches.

PARTS REFERENCE

PARTS REFERENCE
Part Descriptions:

AIRBED
"2 IN 1" VALVE
HANDLE
STORAGE POCKET
FOAM VACUUM VALVE

INFLATION SWITCH
ADJUSTING SWITCH
REMOTE CONTROL
AC LINE CORD
AIR PASSAGE

NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.

INFLATION

Make sure the "2 in 1" valve is securely closed. See Fig (1).
Plug in the AC line cord into an AC electrical outlet. See Fig (2).

Open the foam vacuum valve on the corner of the sleeping surface of bed. See Fig (3).

Press "I" to switch ON. See Fig (4).
When the airbed is fully inflated to the desired firmness, press "O" to switch OFF. See Fig (5).
Pat on the bed surface to adjust the foam.
NOTE: Leave the vacuum valve open to allow the foam to re-shape itself, this may take up to five minutes before initial use.
Close the foam vacuum valve. See Fig (6).
Lie down on the airbed to test the firmness.
If the sleeping surface is too hard, adjust the firmness by pressing and holding the adjusting switch. Air will exit through the air passage. See Fig (7). Release the adjusting switch when the desired firmness is achieved. If the airbed becomes too soft repeat steps #4, #5, #8 and #9 as necessary.

Do not hold the adjusting switch for more than 30 continuous seconds, as overheating will occur. Wait 10 minutes before using again to allow cooling.
Disconnect the AC line cord from the wall socket; place the line cord and the remote control in the storage pocket. See Fig (8).

IMPORTANT NOTE
Proper inflation of the airbed.
The ambient temperatures of air have an effect on the airbed internal pressure. At low ambient temperature the air will contract within the airbed and the airbed will feel softer: add air as necessary. At high ambient temperature the air within the airbed will expand significantly and the airbed will become hard and may burst: release air to avoid damage to the airbed or to soften the feel. Do not expose the airbed to extreme temperatures (hot or cold).
Air inside of bed may expand and contract with varying temperature leading to reduce pressure inside of the bed. If this occurs, simply add more air using the pump to achieve desired firmness. If puncture occurs, please refer to instruction. Repair kit/patch is enclosed.
Stretching is a natural characteristic of new vinyl. During initial use, the airbed may become soft and require additional inflation to maintain desired firmness. This is normal for the first few days of use.
Dimensions shown are approximate and will vary due to the vinyl temperature and the air temperature.
In no event shall Intex, their authorized agents or employees be liable for damages (such as pin holes) to the airbed caused by negligence, ordinary wear and tear, abuse and carelessness, or external forces.

DEFLATION

Unscrew the exhaust valve cap from the "2 in 1" valve. See Fig (9).
Open the foam vacuum valve on the corner of the sleeping surface of bed. See Fig (3).
Begin rolling the airbed from the foot of the airbed towards the head of the airbed where the pump is located, let the airbed stand with the valve open for a while to let any remaining air to flow out of the valve. See Fig (10). Make sure to screw the exhaust valve cap back into the "2 in 1" valve. See Fig (1).
Place the line cord and the remote control in the storage pocket.

INFLATION OPTION

If electrical power is not available then a conventional foot or manually operated air pump can be connected to the optional "2 in 1" valve for inflation.
Pull the valve cap out from the "2 in 1" valve and insert the air hose of a conventional foot or manually operated air pump. See Fig (11).
Start inflating with foot or hand pump, inflate to desired firmness.

Inflate only with a low pressure inflator. Do not over inflate. Fill with cold air only.

STORAGE

Deflate the airbed following the "DEFLATION" instructions.
Make sure the airbed is clean and dry.
Lay bed flat with sleeping surface facing upwards and follow the folding steps on Figs (12 - 16).
Fold the airbed loosely and avoid sharp bends, corners and creases which can damage the airbed.
Place the airbed inside the storage bag and store in a dry, cool storage location.

©2011 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd. - Intex Recreation Corp.
All rights reserved
Printed in China/I
®™ Trademarks used in some countries of the world under license from/®™
Intex Trading Ltd., Intex Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed in the European Union by Intex Trading B.V., P.O. Box nr. 1075 – 4700 BB Roosendaal – The Netherlands
Consumer Service 1-800-234-6839
READ AND SAVE THESE INSTRUCTIONS