Settings Menu; Main Zone; Additional Zone; Information - Daikin EWAA008D2V3P-H Installation Manual

To define the setpoint mode
To use the weather-dependent curve, you need to define the correct
setpoint mode:
Go to setpoint mode ...
Main zone – Heating
[2.4] Main zone > Setpoint
mode
Main zone – Cooling
[2.4] Main zone > Setpoint
mode
Additional zone – Heating
[3.4] Additional zone >
Setpoint mode
Additional zone – Cooling
[3.4] Additional zone >
Setpoint mode
To change the type of weather-dependent curve
To change the type for all zones (main + additional), go to [2.E] Main
zone > WD curve type.
Viewing which type is selected is also possible via [3.C] Additional
zone > WD curve type
To change the weather-dependent curve
Zone
Main zone – Heating
Main zone – Cooling
Additional zone – Heating
Additional zone – Cooling

INFORMATION

Maximum and minimum setpoints
You cannot configure the curve with temperatures that are
higher or lower than the set maximum and minimum
setpoints for that zone. When the maximum or minimum
setpoint is reached, the curve flattens out.
To fine-tune the weather-dependent curve: slope-offset curve
The following table describes how to fine-tune the weather-
dependent curve of a zone:
You feel ...
At regular outdoor At cold outdoor
temperatures ... temperatures ...
OK Cold
OK Hot
Cold OK
Cold Cold
Cold Hot
Hot OK
Hot Cold
Hot Hot
To fine-tune the weather-dependent curve: 2-points curve
The following table describes how to fine-tune the weather-
dependent curve of a zone:
EWAA004~008D + EWYA004~008D
Packaged air-cooled water chillers
and packaged air to water heat pumps
4P688014-1D – 2022.10
Set the setpoint mode to ...
WD heating, fixed cooling
OR Weather dependent
Weather dependent
WD heating, fixed cooling
OR Weather dependent
Weather dependent
Go to ...
[2.5] Main zone > Heating WD
curve
[2.6] Main zone > Cooling WD
curve
[3.5] Additional zone >
Heating WD curve
[3.6] Additional zone >
Cooling WD curve
Fine-tune with slope and
offset:
Slope Offset
↑ —
↓ —
↓ ↑
— ↑
↓ ↑
↑ ↓
↑ ↓
— ↓
You feel ...
At regular outdoor At cold outdoor
temperatures ... temperatures ...
OK Cold
OK Hot
Cold OK
Cold Cold
Cold Hot
Hot OK
Hot Cold
Hot Hot
(a)
See "8.3.2 2-points curve" [ 4 32].
8.4

Settings menu

You can set additional settings using the main menu screen and its
submenus. The most important settings are presented here.
8.4.1

Main zone

Ext thermostat type
Only applicable in external room thermostat control.
NOTICE
If an external room thermostat is used, the external room
thermostat will control the room frost protection. However,
the room frost protection is only possible if [C.2] Space
heating/cooling=On.
# Code
[2.A] [C–05] External room thermostat type for the
main zone:
▪ 1: 1 contact: The used external room
thermostat can only send a thermo
ON/OFF
separation between heating or cooling
demand.
▪ 2: 2
room thermostat can send a separate
heating/cooling
condition.
8.4.2

Additional zone

Ext thermostat type
Only applicable in external room thermostat control. For more info
about the functionality, see "8.4.1 Main
# Code
[3.A] [C–06] External room thermostat type for the
additional zone:
▪ 1: 1 contact
▪ 2: 2 contacts
8.4.3 Information
Dealer information
The installer can fill in his contact number here.
# Code
[8.3] N/A Number that users can call in case of
problems.
8 Configuration
Fine-tune with
setpoints:
(a) (a) (a) (a)
Y2 Y1 X1 X2
↑ — ↑ —
↓ — ↓ —
— ↑ — ↑
↑ ↑ ↑ ↑
↓ ↑ ↓ ↑
— ↓ — ↓
↑ ↓ ↑ ↓
↓ ↓ ↓ ↓
Description
condition. There is no
contacts: The used external
thermo ON/OFF
zone" [ 4 33].
Description
Description
Installation manual
33