Step 2: Hookup - Sony KP-53S65 Service Manual

Step 2: Hookup

Although you can use either an indoor or outdoor
antenna with your projection TV, we recommend that
you connect an outdoor antenna or a cable TV system
to get better picture quality.
Connecting an antenna
Connect your antenna cable to the VHF/UHF antenna
terminal. If you cannot connect your antenna cable
directly to the terminal, follow one of the instructions
below depending on your cable type.
(Rear of projection TV)
A
VHF/UHF
75-ohm coaxial cable
• VHF only
or
• VHF/UHF
or
• Cable
(Rear of projection TV)
B
VHF/UHF
• VHF only 300-ohm twin lead cable
or
• UHF only
or
• VHF/UHF Antenna connector
75-ohm coaxial cable
C
• VHF
(Rear of projection TV)
VHF/UHF
and
EAC-66 U/V mixer
(not supplied)
• UHF
300-ohm twin lead cable
Notes
• Most VHF/UHF combination antennas have a signal splitter.
Remove the splitter before attaching the appropriate connector.
• If you use the U/V mixer, snow and noise may appear in the
picture when viewing cable TV channels over 37.
6 -EN
Getting Started
Connecting an antenna/cable TV
system without a VCR
To cable or antenna
(Rear of projection TV)
VHF/UHF
Cable
To cable box
If your cable company requires you to connect a cable
box, make the connection as follows:
(Rear of projection TV)
VHF/UHF
Cable
IN OUT
Cable box
To cable box and cable
(Rear of projection TV)
AUX
Cable box
TO
CONVERTER
75-ohm coaxial
cable (not supplied)
VHF/UHF
CATV cable
Pay cable TV systems use scrambled or encoded signals
requiring a cable box* in addition to the normal cable
connection.
* The cable box will be supplied by the cable company.
Note
• You cannot watch the signal through an AUX connector as a
window picture.
To cable and antenna
(Rear of projection TV)
AUX
CATV cable
TO
CONVERTER
VHF/UHF
Antenna cable
Note
• Do not connect anything to the TO CONVERTER connector in
this case.
Connecting an antenna/cable TV system with a VCR
For details on connection, see your VCR instruction
manual.
Before making the connection, disconnect the AC power
cords of the equipment to be connected.
To a conventional VCR
Notes
• To connect a monaural VCR, connect the audio output of the VCR
to AUDIO-L (MONO) of VIDEO 1/2/3 IN on the projection TV.
Without a cable box
(Rear of projection TV)
AUX
IN
VIDEO 1 VIDEO 3
TO
CONVERTER
OUT
MONITOR AUDIO
S VIDEO
(VAR/FIX)
VIDEO
VHF/UHF
L
CONTROL S
(MONO)
OUT
AUDIO
R
VIDEO (yellow)
AUDIO-L (white)
AUDIO-R (red)
VMC-810S/820S
(not supplied)
With a cable box
(Rear of projection TV)
AUX
IN
VIDEO 1 VIDEO 3 TO
CONVERTER
OUT
MONITOR AUDIO
S VIDEO
(VAR/FIX)
VIDEO
VHF/UHF
L
CONTROL S (MONO)
OUT AUDIO
R
VIDEO (yellow)
AUDIO-L (white)
AUDIO-R (red)
VMC-810S/820S
(not supplied)
After making these connections, you will be able to do
the following:
• View the playback of video tapes
• Record one TV program while viewing another
program
• Watch two TV programs at once using PIP
VHF/UHF
Antenna cable
VHF/UHF
output
VCR
OUT
AUDIO VIDEO
Antenna cable
LINE
IN
OUT
VHF/UHF
input
Video and audio
outputs
VHF/UHF
Antenna cable
VCR
OUT
AUDIO VIDEO
LINE
IN
OUT
Video
and
audio
VHF/UHF
outputs
input
VHF/UHF
output
Cable box
Antenna
cable
OUT
IN
Splitter (not supplied)
7 -EN
Getting Started
EN