Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ryobi RMS305DB
Summary of Contents for Ryobi RMS305DB
- Page 1 ORIGINAL INSTRUCTIONS Dual Bevel Sliding Mitre Saw RMS305DB...
- Page 2 Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining the product. Subject to technical modification.
-
Page 3: Intended Use
Safety, performance, and dependability have been given Water entering a power tool will increase the risk of top priority in the design of your mitre saw. electric shock. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. INTENDED USE Keep cord away from heat, oil, sharp edges or The mitre saw is intended for sawing solid and bonded... -
Page 4: Safety Instructions For Mitre Saws
Disconnect the plug from the power source and/ and push the saw through the workpiece. Cutting on or remove the battery pack, if detachable, from the pull stroke is likely to cause the saw blade to climb the power tool before making any adjustments, on top of the workpiece and violently throw the blade changing accessories, or storing power tools. -
Page 5: Additional Safety Warnings
hand into the blade. Ensure the saw blade is mounted correctly, tighten the Let the blade reach full speed before contacting the 12-15 Nm). workpiece. This will reduce the risk of the workpiece being thrown. Fastening screw and nuts shall be tightened using the appropriate spanner, etc. -
Page 6: Residual Risks
correctly. harmful to health. Use a dust suction system and wear a suitable dust protection mask. Remove deposited The lower blade guard should only open when the dust thoroughly with a vacuum cleaner. blade is lowered to the workpiece and must always be able to move freely and close automatically. -
Page 7: Maintenance
WARNING WARNING Dust from certain paints, coatings and materials may For greater safety and reliability, all repairs should be cause irritation or allergic reactions to the respiratory performed by an authorised service centre. system. Dust from wood such as oak, beech, MDF and others are carcinogenic. -
Page 8: Symbols On The Product
Laser radiation. SYMBOLS ON THE PRODUCT Class 2 laser product Safety alert Waste electrical products should not be disposed of with household Regulatory Compliance Mark waste. Please recycle where (RCM). Product meets applicable regulatory requirements. Local Authority or retailer for Please read instructions... - Page 9 2 mm 4 mm 5 mm D13 x D8 x 1.6mm...
- Page 10 1. Handle, insulated gripping surface 2. Power switch 3. Safety lock lever 21. Blade 4. Upper guard 22. Laser switch 5. Lower guard 23. Spindle lock button 24. Bracket stop 25. Linear rod stop knob 8. Turntable Screws for locking main fence 9.
- Page 11 22 23...
- Page 12 RMSS100...
- Page 14 p.14 p.14 p.15 p.15 p.16 p.17 p.18 p.21...
- Page 15 p.25 p.32 p.34 p.26 p.37 p.28 p.31 p.40...
- Page 16 90º 90º...
- Page 29 2 mm...
- Page 40 5 mm 5 mm 5 mm 5 mm...
- Page 42 90º...
-
Page 44: Product Specifications
PRODUCT SPECIFICATIONS NOISE LEVEL Mitre saw WARNING The declared noise emission value(s) have been measured Model RMS305DB Net weight 18.5 kg tool with another. Blade diameter 305 mm The declared noise value(s) may also be used in a Arbor hole... -
Page 45: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Mitre saw will not start. No power to the saw. Check that the power cord is connected to a live power source. Wood burns at ends of cut. Dirty blade. Clean blade. Worn blade. Replace worn blade. Workpiece is binding. - Page 48 Techtronic Industries Australia Pty Ltd 31 Gilby Road, Mount Waverley, VIC, 3149, Australia RYOBI is a trademark of Ryobi Limited, Techtronic Industries N.Z. Limited and is used under license. Unit C, 70 Business Parade South, © 2019 Techtronic Cordless GP. All rights reserved.