The features section starting on page 32 of this manual will describe these settings. Most setting have been preset for optimal performance. If you need any assistance with installation or setup of your new Hunter Thermostat, please call us, our technical support staff are ready to help!
Page 4
Know Your Thermostat 1. Enters Schedule Setup for altering scheduled programs. 2. Sets the Home Today feature for when you are home during a regularly scheduled Away period. 3. Sets the Save Away feature for when you will not be home during a regularly programmed time.
Page 6
Know Your Thermostat 1. Holds 2 “AA” Batteries. 2. HE/HG Switch - allows you to set your furnace to Gas/Oil or Electric, based on the type of system you have. 3. Conventional/Heat Pump System Switch - Allows your thermostat to operate your HVAC system properly by selecting the system type that you have.
Page 8
Know Your Thermostat 1. Shows the current day of the week or weekend. 2. Indicates the thermostat is running in schedule mode. 3. Flashes when the furnace filter should be checked for replacement. 4. On when the current schedule period is running. 5.
Setting Day and Time Once you install the batteries, the thermostat will prompt you to set the current day and time. 1. You will notice that “Mon” will be flashing at the top left of your screen. Use the buttons to move to your current day of the week and press the button to Next advance to the next step.
Scheduling Introduction Read the scheduling section thoroughly to ensure you understand your scheduling options and which will best fit with your lifestyle. The following notes should help you with scheduling: * The schedule time can be set in 15 minute increments, and remains the same for both Heat and Cool programs.
Setting Your Schedule 1. Press the Schedule Button to enter Scheduling mode. 2. Use the buttons to select “On” and then to move forward to Scheduling. Next Note: If you do not wish to use the scheduling option on your thermostat, refer to page 22, step 2.
Page 16
Setting Your Schedule 6. Set the temperature for your heating cycle as indicated by the flashing ”Heat to” icon on your screen. Use the buttons to change the temperature and press . You will Next be asked to set your cooling cycle, indicated by the flashing “Cool to”. Set this temperature with your buttons and hit Next...
Page 18
Setting Your Schedule 10. The day select screen will now show “Copy Day” and ask you if you wish to copy the day you just scheduled to any other days. Select “YES” and or see step 13 for selecting Next “NO”.
Temporary Temperature Change With Temporary Temperature Change you have the ability to alter the temperature for only the current running schedule. 1. Press the button once to activate the screen, the backlight will come on. 2. Use the buttons again to select a new temperature. 3.
Turning Off Scheduling To turn off your schedule and have the thermostat permanently set to one temperature: 1. Press the button once. Schedule 2. Use the button to switch to Off and select Done/ Home 3. The screen will show “Updated!” and return you to the home screen. Note: You will notice the black bar on the screen beside the Schedule button is not displayed anymore.
Home Today The Home Today feature allows you to override your schedule for 1 day. It can be used for example if you are home on a day when you would normally have the thermostat‘s “Away” mode active. When used, the Home Today feature will select your At Home temperature to run at for the course of the day until your scheduled Asleep time starts, then revert back to running your normal schedule.
Save Away The Save Away feature allows you to set a lower or higher temperature for the time you will be away from your home outside of your normal Away schedule. This can include days you will be away for vacation, or a few hours away from your home. The Save Away feature can be set for as little as 1 hour or as much as 30 days.
Alerts This chapter will outline the various alerts the thermostat will report to you and how to respond to them. 1. Low Battery: This icon will appear when your batteries are starting to run low on power and should be changed to avoid system interruptions, (Figure 1) Change the batteries by gripping the sides of the thermostat firmly and pulling straight back, (Figure 1a).
Menu Options Under your menu options you have the ability to reset your filter counter, change your day/time, span settings, temperature measurement, as well as locking the thermostat. After making changes to each menu option, the thermostat will show “Updated” and save your changes. To access these options: 1.
Page 34
Menu Options 5. SPAN 1: The next menu option is to set your thermostats primary span. Use the buttons to adjust between 1, 2, or, 3 degrees. Press , the screen will flash Next “Updated” and return to menu options or press to return to the home screen.
Page 36
Menu Options 1. LOCK/UNLOCK: Allows you to lock the thermostat so random keypress’ will not change your settings. Use the buttons to change between “YES” and “NO”. Choose “YES” to lock the thermostat or “NO” to keep the thermostat unlocked. Press , the screen will flash “Updated”...
Energy Saver Bar The Energy Saver Bar indicates estimated energy savings. The preset schedules in the thermostat have been designed to give you optimal energy savings, five bars. Altering these schedules has a direct impact on the energy saver indicator. Altering the temperatures and/or times that the schedules run could decrease the estimated energy savings.
Additional Features Armchair Programming There is no need to stand at the wall where the thermostat is mounted while programming or changing settings. Simply remove the thermostat from the wall and make the necessary changes in the comfort of a chair. You can also set your programming and settings before you even install the thermostat.
Page 42
Troubleshooting and Support Problem: Fan runs continuously. Solution: 1. Check fan setting to see if it is set to on. 2. Move HG/HE switch to opposite position. Problem: Heating or cooling does not turn on or off. Solution: 1. Check the system is in the right mode (heat or cool). 2.
Technical Support If you need any assistance with installion or setup of your new Hunter Thermostat, please call us, our technical support staff is ready to help! USA: 1-888-830-1326 Canada: 1-866-268-1936 Hours of operation are from 7:00 am to 7:00 pm Monday - Friday and 8:00 am to 5:00 pm on Saturday, Central Time.
IN RESPECT TO YOUR HUNTER THERMOSTAT IS LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE. This warranty is voided if your Hunter Thermostat is not purchased and used in the USA. This warranty excludes and does not cover defects, malfunctions or failures or...
Page 45
1 Year Guarantee Suite 400, Memphis, TN 38016. You will be responsible for all insurance and freight or other transportation charges to our factory. We will return your Hunter Thermostat freight prepaid. Your Hunter Thermostat should be properly packed to avoid damage in transit since we will not be responsible for any such damage.