Comcast Xfinity XR2 - Remote Control Start Manual

Also See for Xfinity XR2:

User manual (2 pages)

Start (2 pages)

Table of Contents

Contents

1 Meet Your Remote
2 Turn On Your Remote
3 Program Your Remote To Control Your Set-Top Box
4 Pair Remote for "Aim Anywhere" Control
5 Control Your TV's Power and Volume
6 Documents / Resources
- 6.1 References
- 6.2 Download manual

Comcast Xfinity XR2 - Remote Control Start Manual

Meet Your Remote

All Power
TV Power
TV Input
Changes to the next available input on your TV (if programmed in Step 4)
Search
Discover content by channel, program or key words.
XFINITY/Menu
Access Guide, Saved, XFINITY On Demand, Apps, Search and Settings.
Number Keys
Swap
Switches between two DVR tuners so you can control playback of two channels.
Setup
Program remote for Aim Anywhere or to control your TV or audio device.

Turn On Your Remote

Install batteries in the remote and turn on your devices.

To set up your remote, first install AA batteries (sold separately). The All Power key will blink green four times as the remote powers up (about 5 seconds).
Turn on your TV.
Turn on your cable box.

Program Your Remote To Control Your Set-Top Box

Your remote is preprogrammed to operate XFINITY cable boxes. If you are using the remote for control of a non-XFINITY cable box, you may need to program the remote for the Motorola or Cisco mode. Follow the steps below to program your remote.

Press the Setup button until the All Power key on the remote changes from red to green.
Press B for control of a Motorola brand cable box; press C for control of a Cisco or Scientific-Atlanta brand cable box.
Note: If you need to re-program the remote for control of an XFINITY cable box, repeat the steps above and press A in step 2.
Press the XFINITY key to check that your remote controls your set-top box. If it does, you're all set. If not, repeat these steps but press C for Cisco mode or A for XFINITY mode in step B.
Once the code is correctly entered, your XFINITY Remote is paired with the device.

Pair Remote for "Aim Anywhere" Control

Control your cable box without having to point at it, even when it is inside a cabinet or entertainment center.
Aim Anywhere is only supported on certain XFINITY cable boxes. To see if your cable box supports Aim Anywhere control visit xfinity.com/remotes

Press the Setup button until the All Power key on the remote changes from red to green.
Press the XFINITY button.
Follow the on-screen instruction to enter the 3-digit code that appears.
Once the code is correctly entered, your XFINITY Remote is paired with the device.

Not working? Make sure to install batteries in the remote, check that your TV is on and that you are entering the correct 3-digit code on your TV screen.
Need to remove Aim Anywhere control? Press and hold the Setup button on the remote until the status LED changes from red to green. Press A on the remote. If the status LED blinks green twice, you have successfully removed Aim Anywhere.

Control Your TV's Power and Volume

Using the list on the right, find the first 5-digit code for your TV manufacturer.
Press and hold the Setup button (about 3 seconds) until the Status LED changes from red to green.
Enter in the first 5-digit code for you TV manufacturer. The Status LED should blink green twice.
Verify that the code was accepted by using your remote to adjust volume and turn the TV on and off.

Popular TV Manufacturer Codes
Emerson	11864, 10171
Insignia	12049, 11641
JVC	11774, 12321
LG	12731, 10178
Magnavox	10054, 12597
Panasonic	11480, 10051
Philips	11867, 12597
RCA	10047, 11447
Samsung	12051, 10702
Sanyo	10154, 11142
Sharp	10093, 12360
Sony	10810, 11685
Toshiba	10156, 11524
VIZIO	11758, 12707
Westinghouse	11712, 13579
If your code isn't listed or you would like to control an audio device, visit xfinity.com/remotes

Not working? Try the second code listed. Still not working? Visit xfinity.com/remotes for a complete list of codes or use the My Account app for mobile (iOS/Android) or X1.