Gree GWH18YD-K6DNA2A Service Manual page 19

2. FAN button
Press this button, Auto, Low, Medium-low, Medium, Medium-high, High speed can be circularly selected. After powered on, Auto fan speed
is default. Under DRY mode, Low fan speed only can be set up.
Low fan Medium-low fan
Note:
It's Low fan speed under Dry mode.
X-FAN function：Hold fan speed button for 2s in COOL or DRY mode, the icon "
for a few minutes in order to dry the indoor unit even though you have turned off the unit. After energization, X-FAN OFF is defaulted.
X-FAN is not available in AUTO, FAN or HEAT mode.
This function indicates that moisture on evaporator of indoor unit will be blowed after the unit is stopped to avoid mould.
Having set X-FAN function on: After turning off the unit by pressing ON/OFF
at low speed. In this period, Hold fan speed button for 2s to stop indoor fan directly.
Having set X-FAN function off: After turning off the unit by pressing ON/OFF
3. MODE button
Press this button, Auto, Cool, Dry, Fan, Heat mode can be selected circularly. Auto mode is default while power on. Under Auto mode, the
temperature will not be displayed;Under Heat mode, the initial value is 28°C( 82°F);Under other modes, the initial value is 25°C(77°F).
4. +/- button
Press " + " or " - " button once increase or decrease set temperature 1°C(°F).
controller will change
When setting TIMER ON, TIMER OFF or CLOCK, press " + " or " - " button to adjust time. (Refer to CLOCK, TIMER ON, TIMER OFF
buttons) When setting
TIMER OFF buttons)
5. TURBO button
Under Cool or Heat mode,press this button can turn on or turn off the Turbo function.After the Turbo function turned on, the signal of Turbo
will display. The signal will be automatically cancelled if changing the mode or fan speed.
6. button
Press this button to set left & right swing angle cycling as below:
7. button
Press this button to set swing angle,which circularly changes as below:
This remote controller is universal. If it receives threes kinds of following status,the swing angle will remain origial.
If guide louver is stopped when it is swinging up and down,it will remain its present position.
8. CLOCK button
Press this button, the clock can be set up,signal
if continuously press this button for 2 seconds above,in every 0.5 seconds, the value on ten place of Minute will be increased 1.During
powered on, 12:00 is defaulted to display and signal
value is Clock value, otherwise is Timer value.
9. TIMER ON/TIMER OFF button
Timer On setting: Signal "ON"will blink and display,signal
During 5 seconds blink,by pressing + or - button to adjust the time value of numerical section,every press of that button,the value will be
increased or decreased 1 minute.Hold pressing + or - button,2 seconds later,it quickly change,the way of change is: During the initial 2.5
seconds,ten numbers change in the one place of minute,then the one place is constant,ten numbers change in the ten splace of minute at
2.5 seconds speed and carry. During 5s blink,press the Timer button,the timer setting succeeds.The Timer On has been set up,repress the
timer button,theTimer On will be canceled. Before setting theTimer,please adjust the Clock to the current actual time.
One press this key to enter into TIMER OFF setup, in which case the TIMER OFF icon will blink. The method of setting is the sameas for
TIMER ON.
16
ATUO
Medium fan
AUTO
quickly. On releasing button after setting is finished, temperature indicator on indoor unit will change accordingly.
TIMER ON, TIMER OFF or CLOCK, press " + " or " - " button to adjust time. (Refer
OFF
blink and display.Within 5 seconds, the value can be adjusted by pressing + or - button,
Medium-high fan
" is displayed and the indoor fan will continue operation
button indoor fan will continue running for a few minutes.
button, the complete unit will be off directly.
COOL DRY FAN
Holding " + " or " - " button, set temperature on remote
OFF
will be displayed. If there is signal
will conceal,the numerical section will become the timer on setting status.
High fan
(only for cooling and heating unit.
As for cooling only unit, it won't
have any action when it receives
the signal of heating operation.)
HEAT
to CLOCK, TIMER ON,
be displayed that denotes the current time
Service Manual
After
Technical Information