Channel Mode Messages - Roland TD-12 Midi Implementation Manual

TD-12 MIDI Implementation
●Pitch Bend Change
Status 2nd byte
EnH llH
n = MIDI channel number:
mm,ll = Pitch Bend value:
* Only the channels assigned to the backing part can be received.
* When recording, this is recorded in the sequencer data itself.

■Channel Mode Messages

* Following Channel Voice Messages can be received in [SETUP]-[MIDI]-[MIDI
CH] Tx/Rx Channel.
* Not received when [SETUP]-[MIDI]-[MIDI CH] Tx/Rx Switch is set to "OFF."
●All Sounds Off (Controller number 120)
Status 2nd byte
BnH 78H
n = MIDI channel number:
* When this message is received, all currently-sounding notes on the
corresponding channel will be silenced. However, the status of channel
messages will not change.
* When recording, this is recorded in the sequencer data itself.
●Reset All Controllers (Controller number 121)
Status 2nd byte
BnH 79H
n = MIDI channel number:
* When this message is received, the following controllers will be set to their reset
values.
Controller
Pitch Bend Change
Polyphonic Key Pressure
Modulation
Breath Controller
Foot Controller
Expression
General Purpose Controller 1 - 4
Hold 1
RPN
* When recording, a control message carrying the reset value will be created and
recorded.
●All Notes Off (Controller number 123)
Status 2nd byte
BnH 7BH
n = MIDI channel number:
* When All Notes Off is received, all notes on the corresponding channel will be
turned off. However if Hold 1 is ON, the sound will be continued until these are
turned off.
* In the recording mode, "Note Off message" will be created for corresponding
Note On message, and will be recorded.
4
3rd byte
mmH
0H - FH (ch.1 - ch.16)
00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
3rd byte
00H
0H - FH (ch.1 - ch.16)
3rd byte
00H
0H - FH (ch.1 - ch.16)
Reset value
+/-0 (center)
0 (off)
0
0
0
0
0
0 (off)
unset; previously set data will not change
3rd byte
00H
0H - FH (ch.1 - ch.16)
●OMNI OFF (Controller number 124)
Status 2nd byte
BnH 7CH
n = MIDI channel number:
* The same processing will be carried out as when All Notes Off is received.
●OMNI ON (Controller number 125)
Status 2nd byte
BnH 7DH
n = MIDI channel number:
* The same processing will be carried out as when All Notes Off is received.
●MONO (Controller number 126)
Status 2nd byte
BnH 7EH
n = MIDI channel number:
mm = mono number:
* The same processing will be carried out as when All Sound Off or All Notes Off
is received.
●POLY (Controller number 127)
Status 2nd byte
BnH 7FH
n = MIDI channel number:
* The same processing will be carried out as when All Sound Off or All Notes Off
is received.
■System Realtime Message
* Following System Realtime Messages cannot be recorded in recording mode.
●Timing Clock
Status
F8H
* Recognized only when the [TEMPO]-[SYNC] Sync Mode is set at "EXTERNAL"
or "AUTO".
●Start
Status
FAH
* Recognized only when the [TEMPO]-[SYNC] Sync Mode is set at "EXTERNAL,"
"AUTO" or "REMOTE".
●Continue
Status
FBH
* Recognized only when the [TEMPO]-[SYNC] Sync Mode is set at "EXTERNAL,"
"AUTO" or "REMOTE".
3rd byte
00H
0H - FH (ch.1 - ch.16)
3rd byte
00H
0H - FH (ch.1 - ch.16)
3rd byte
mmH
0H - FH (ch.1 - ch.16)
00H - 10H (0 - 16)
3rd byte
00H
0H - FH (ch.1 - ch.16)