Oregon Scientific WMR200/WMR200A - Professional Weather Center Manual

WIND SENSOR / TEMPERATURE & HUMIDITY SENSOR

SOLAR PANEL

RAIN GAUGE

ASSEMBLY PARTS

ACCESSORIES - SENSORS

This product can work with up to 10 sensors at any one time to capture outdoor temperature, relative humidity or UV readings in various locations.
Optional wireless remote sensors such as those listed below can be purchased separately. For more information, please contact your local retailer.*

• Thermo-hygro THGR800 (3-Ch)
• Thermo-hygro THGR810 (10-Ch)
• UV UVN800

* Features and accessories will not be available in all countries.

OVERVIEW

FRONT VIEW

1. MEM: View current, maximum and minimum readings
2. CH: Toggle between 10 different channels
3. AL: Set and view status of Clock and HI / LO alarms
4. SET: Enter setting modes
5. Antenna
6. UP / DWN: Increase / decrease the values of the selected readings
7. AL ON/OFF: Turn alarms on and off
8. UNIT: Change display units

BACK VIEW

1. USB socket
2. Backlight (continuous) On/Off
3. Battery compartment
4. AC / DC socket
5. Wall mount holes / Adjustable table stand
6. RESET: Reset unit to default settings
7. EU/UK slide switch (WMR200 only)

LCD DISPLAY

1. Indicates a successful USB connection
2. Indicates low battery
3. Indicates no main power supply
4. Barometer area
5. Rainfall area
6. UV area
7. Clock / alarm / moon phase area
8. Weather forecast area
9. Outdoor temperature and humidity area
10. Wind area
11. Bar chart area
12. Indoor temperature / humidity area

DETAILED LCD DISPLAY VIEW

BAROMETER

1. Altitude indicator
2. Altitude / pressure reading
3. 0 (current) to – 24 hours barometer record
4. Indicates pressure alarm is ON
5. User selectable altitude / pressure measurement unit

UV

1. 0 (current) to – 10 hours UV record
2. UV level index
3. Sensor batteries low
4. Indicates high UV alarm is ON
5. UVI reading

CLOCK / MOON PHASE

1. Displays time of records, time stamp for Indoor / Outdoor temperature / humidity sensors and initial date set (Since date) for rainfall.
2. Radio controlled clock
3. indicates daily alarm is ON
4. Displays Clock with seconds, Clock with day, Calendar, Data logger
5. Data Logger displaying remaining number of days memory will allow for data collection
6. Set Data Logging frequency (refer to Memory section)
7. Moon phase display
8. Offset time zone

OUTDOOR TEMPERATURE / HUMIDITY

1. Indicates HI / LO outdoor temperature alarms are ON
2. MAX / MIN temperatures (refer to date stamp on clock area for more details)
3. Sensor batteries low
4. Displays from 1-10 outdoor sensors
5. Heat index
6. Outdoor Temperature readings
7. Temperature trend indicators
8. Dew point temperature
9. MAX / MIN humidity

10. Indicates HI / LO outdoor humidity alarms are ON
11. Humidity trend indicators
12. User selectable temperature units

INDOOR TEMPERATURE AND HUMIDITY

1. Indicates HI / LO temperature alarms are ON
2. MAX / MIN temperatures
3. Heat index
4. Indoor temperature reading
5. Temperature trend indicators
6. Dew point temperature
7. MAX / MIN indoor humidity
8. Indicates HI / LO humidity alarms are ON
9. Humidity trend indicators
10. User selectable temperature units

WIND SPEED / DIRECTION / WIND CHILL

BAR CHART

1. Bar chart icon area
2. Barometer bar chart display
3. Rainfall bar chart display
4. UV bar chart display
5. Measurement axis

WIND SENSOR

1. Wind Direction
2. Wind vane casing
3. Anemometer
4. Solar power socket

RAIN GAUGE

Base and funnel:

1. Rain Gauge
2. Battery compartment
3. RESET button

1. Funnel
2. Indicator

OUTDOOR TEMPERATURE / HUMIDITY SENSOR

1. Temperature / humidity sensor casing
2. Solar power socket
3. RESET button
4. Battery compartment

GETTING STARTED

SET UP REMOTE WIND SENSOR

The wind sensor takes wind speed and direction readings. The sensor is battery and solar powered operated. It is capable of transmitting data to the base station wirelessly within an approximate operating range of 100 meters (328 feet).

Ensure that the wind sensor is pointing North to enable it to record accurate readings.
NOTE
The sensor should be positioned in an open area away from trees or other obstructions.

To insert batteries:

1. Unscrew the anemometer from the wind sensor carefully.
   
   
2. Insert batteries matching the polarities (+ / -) and replace the anemometer. Press RESET after each battery change.
   
   
3. Slide wind vane onto the end of the plastic attachment located on the aluminium pole.
   

NOTE
Use alkaline batteries for longer usage and consumer grade lithium batteries in temperatures below freezing.

SET UP REMOTE TEMPERATURE / HUMIDITY SENSOR

1. Holding sensor, twist and click to the left.
   
   
2. Pull sensor away from casing.
3. Insert batteries matching the polarities (+ / -). Press RESET after each battery change.
   
   
4. Insert sensor into the casing, twist and click to the right to secure.
   
   
5. Slide temperature and humidity sensor onto the smaller end of the sensor connector.

REMOTE UNIT ASSEMBLY

1. Insert the cone-shaped end into the pole.
   
   
2. Using 2 screws, fix it firmly into place.
3. Insert the versatile plastic base into the pole. Align the holes of the pole with the holes of the plastic base.
   
   
4. Secure the plastic base by inserting the screw and screwing it tightly into the holes of the plastic base and pole.
5. Hammer pole (cone end down) into the ground at the desired spot until versatile plastic base is level with the ground.
   
   The sensor should be positioned in an open area away from trees or other obstructions.
   TIP
   Place a block of wood between the pole and the hammer to prevent damage to the pole.
   

6. Assemble middle pole on top of the bottom one.
   
   
7. Using two screws, fix it firmly into place.
8. Assemble top pole on top of the middle one.
   
   
9. Using two screws, fix it firmly into place.
10. Slide the vertical attachment bracket on top of the top pole.
    
    
11. Using two screws, fix it firmly into place.
    

To mount the temperature / humidity sensor:

12. Slide outdoor sensor onto vertical attachment bracket.
    

13. Slide the solar panel connector into place on the opposite side of the bracket. Slot the solar panel in place.
    
    
14. Adjust the solar panel. Once facing desired direction, use screw to fix in place.
15. Loosen the wing bolt and adjust the angle. Tighten wing bolt to secure solar panel at desired angle.

NOTE
For best results, direct solar panel as follows:

Solar panel facing:	if you reside in the:
North	Southern Hemisphere
South	Northern Hemisphere

To mount the wind sensor:

16. Insert the wind vane into the attachment bracket.
    
    
17. Screw aluminum pole firmly into place.
    
    For best results, point the wind vane North.

18. Remove outdoor sensor from casing. Plug one solar panel cable into the socket.
    
    
19. Replace sensor into the casing.
20. Plug the other solar panel cable into the socket on the wind vane.
    
    This will provide the sensors with an additional power supply.
    NOTE
    There are slots to insert the solar power cables for convenient storage. There are also fasteners to help tighten the cables.
    NOTE
    The solar panel is an energy saving feature, which is an environmentally friendly way to provide additional power to the sensors and prolongs battery life. However, it cannot replace battery power entirely. Sensors can operate entirely on battery power.

Securing the assembled remote unit:

21. Insert the 2 rectangular base legs through the holes of the versatile base and hammer down.
    
    
22. Using the string, tie a knot on the eye pins. Hammer each eye pin into the ground at a 90° angle.
    
    
    Using the fasteners, tighten the string. To tighten, pull fastener down. To loosen, thread the string up through the fastener eyelets.
    

ALTERNATIVE SET UP: REMOTE WIND SENSOR ON EXISTING POLE

1. Secure the plastic base onto existing pole with U-bolts, washers and bolts.
   
   
2. Insert the horizontal attachment bracket into the base.
   
   
3. Using a screw, fix firmly into place.

4. Insert wind sensor into the top of the bracket.
   
   
5. Using screws, fix aluminum pole firmly into place.
6. Slide outdoor sensor onto bracket.
   
   For best results, point the wind vane North.
   
   

7. Slide the solar panel connector into place on the other side of the bracket. Slot the solar panel in place.
   
   
8. Adjust the solar panel. Once facing desired direction, use screw to fix in place.
9. Loosen the wing bolt and adjust the angle. Tighten wing bolt to secure solar panel at desired angle.
10. Remove outdoor sensor from casing. Plug one solar panel cable into the socket. Replace sensor into the casing.
    
    NOTE
    For best results, direct solar panel as follows:

    Solar panel facing:	If you reside in the:
    North	Southern Hemisphere
    South	Northern Hemisphere

11. Plug the other solar panel cables into the socket on the wind vane.
    
    NOTE
    There are slots to insert the solar power cable for convenient storage. There are also fasteners to help tighten the cables.
    

ALTERNATIVE SET UP: TEMPERATURE / HUMIDITY SENSOR MOUNTED SEPARATELY

1. Insert 4 type A screws into the holes of the sensor connector. Screw firmly into place, i.e., fence.
   

SET UP RAIN GAUGE

The rain gauge collects rain and takes readings of rainfall rate and the total rainfall over a period of time. The sensor can remotely transmit data to the base station. The base station and rain gauge should be positioned within an effective range: about 100 meters (328 Feet) in an open area. The rain gauge should be mounted horizontally about 1 meter (3 feet) from the ground in an open area away from trees or other obstructions to allow rain to fall naturally for an accurate reading.
To set up the Rain Gauge:

1. Remove screws and slide the cover off in an upwards motion.
   
   
2. Insert the batteries (2 x UM-3 / AA), matching the polarities (+ / -). Press RESET after each battery change.
   
   
3. Remove the fibre tape.
   

To ensure a level plane:
Put a few drops of water on the cross at the base of the funnel to check the horizontal level.

Water will pool to the center of the cross when the rain gauge is level. If water remains on 1-4, the gauge is not horizontal. If necessary, adjust the level using the screw.

NOTE
For best results, ensure the base is horizontal to allow maximum drainage of any collected rain.

SET UP BASE STATION

NOTE
Install batteries matching the polarities (+ / -) in the remote sensor before installing the base station. For continuous use, install the AC adapter. The batteries are for back-up use only.

NOTE
Make sure the adapter is not obstructed and is easily accessible to the unit.
NOTE
The base station and adapter should not be exposed to wet conditions. No objects filled with liquid, such as vases, should be placed on the base station and adapter.

INSERT BATTERIES

1. Remove the battery compartment.
2. Insert the batteries, matching the polarities (+ / -).
3. Press RESET after each battery change.

NOTE
Do not use rechargeable batteries. It is recommended that you use alkaline batteries with this product for longer performance.
NOTE
Batteries should not be exposed to excessive heat such as sunshine or fire.

LOCATION	MEANING
Weather forecast area	Base station batteries low
Rainfall / UV / Wind / Outdoor temperature / humidity area	Sensor batteries low

SENSOR DATA TRANSMISSION

To search for a sensor:

1. Select desired area to activate.
2. Press and hold CH and MEM.
3. 
   icons will flash for 5 minutes.
   NOTE
   Unit will search only for already registered sensors or new sensors reset within last 30 minutes. To register a new sensor, reset sensor prior to search.
   The sensor reception icon in the remote sensor area shows the status:

   ICON	DESCRIPTION
   	Base station is searching for sensor(s)
   	A channel has been found
   	Sensor 1 data received
   	The sensor cannot be found.

   TIP
   The transmission range may vary depending on many factors. You may need to experiment with various locations to get the best results.

CLOCK

CLOCK RECEPTION

This product is designed to synchronize its clock automatically with a clock signal.
WMR200:
Slide switch to EU / UK to select the desired signal.

• EU: DCF-77 signal: within 1500km (932 miles) of Frankfurt, Germany.
• UK: MSF-60 signal: within 1500km (932 miles) of Anthorn, England.

WMR200A:
WWVB-60 signal: within 3200km (2000 miles) of Fort Collins Colorado. Manually set clock to select time zone (Pacific, Mountain, Central or Eastern).
indicates the status of the clock reception signal.

ICON	MEANING
	Time is synchronized Receiving signal is strong
	Time is not synchronized Receiving signal is weak

NOTE
Reception takes 2-10 minutes. If the signal is weak, it can take up to 24 hours to get a valid signal.

To enable / disable signal reception:
Press and hold clock area to enable / disable signal reception. A beep will sound to confirm action.
NOTE
For best reception, the base station should be placed on a flat, non-metallic surface near a window in an upper floor of your home. The antenna should be placed away from electrical appliances and not be moved around when searching for a signal.

MANUALLY SET CLOCK

1. Press clock area to activate.
2. Press SET to toggle between time zone offset, 12/24 hr format, hour, minute, year, day / month, month, day, time zone.
3. Once in desired setting, press UP or DWN to change the settings.
4. Press:
   • SET to confirm and continue to next setting OR
   • touch panel area (except tool bar) to confirm and exit.

WMR200: Time zone offset sets the clock +/- 23 hours from the received clock signal time.
WMR200A: Select the time zone: (PA) Pacific, (EA) Eastern, (CE) Central or (MO) Mountain.
NOTE
The language options are English (E), German (D), French (F), Italian (I), and Spanish (S).

To select clock display mode:
Press clock area repeatedly to toggle between:

• Clock with seconds
• Clock with weekday
• Date with year
• Data logger (please refer to Memory / Data logger section)

PRESSURE

To toggle barometer unit:

1. Press barometer area to toggle between Altitude / current barometer.
2. Press UNIT to select FEET / M or inHg / mmHg / mb / hPA.

SET ALTITUDE

Set the altitude to reflect distance from sea level at your position.

1. Press barometer area to display ALT.
2. Press SET.
3. Press UP / DWN to set the altitude in 10 m (33 ft) increments from -100 m (-328 ft) to 2500 m (8202 ft).
4. Press SET or touch panel area (except tool bar / forecast area) to confirm.

RAINFALL

To select rainfall display mode:
Press rain area to toggle between:

• Rain rate
• Hourly Rainfall
• Accumulated rainfall
• Rainfall recorded in the past 24 hours

Press UNIT to select mm / in.

ACCUMULATED RAINFALL

To display SINCE DATE:

1. Press rain area repeatedly until Accumulated Rainfall is displayed. (Clock area will display the start date / time of rainfall recording).

To reset SINCE DATE:
Press and hold MEM to set current time as start of accumulated rainfall records.

UV

The UV index levels are as follows:

UV INDEX	DANGER LEVEL	ICON
0-2	Low
3-5	Moderate
6-7	High
8-10	Very high
11 and above	Extremely high

WEATHER FORECAST

This product forecasts the next 12 to 24 hours of weather within a 30-50 km (19-31 mile) radius (US- with a 75% accuracy).

	Sunny
	Clear night
	Partly cloudy
	Partly cloudy at night
	Cloudy
	Rainy
	Snowy

TEMPERATURE AND HUMIDITY

To toggle temperature unit:

1. Press Indoor / Outdoor Temperature / Humidity area.

2. Press UNIT to select °C / °F.

To auto-scan between sensors (Outdoor):

1. Press Outdoor Temperature / Humidity area.
2. Press and hold CH to display data for each sensor.

AUTO SCANNING FUNCTION

To activate the outdoor temperature and humidity auto-scan function:

1. Press and hold CH to activate auto-scan. The temperature and humidity display will scroll from indoor to ch1 through to ch10.
2. Press CH / MEM to stop the auto-scan.

NOTE
Channel 1 is used for the outdoor temperature and humidity sensor provided in this package. Additional temperature and humidity sensors can use other channels.
To change channel:
Press CH to change channel.

TEMPERATURE AND HUMIDITY TRENDS

The temperature and humidity trend icons are based on recent sensor readings.
The trend lines are shown next to the temperature and humidity readings. The trend is shown as follows:

RISING	STEADY	FALLING

HEAT INDEX

Press Indoor / Outdoor Temperature / Humidity area to display the actual temperature felt:

TEMPERATURE RANGE		MEANING
27°C to 32°C (80°F to 89°F)		Possibility of heat exhaustion
32°C to 40°C (90°F to 104°F)	Extreme Caution	Possibility of heat dehydration
41°C to 54°C (105°F to 129°F)		Heat exhaustion likely
54°C to 92°C (130°F to 151°F)	Extreme danger	Strong risk of dehydration / sun stroke

NOTE
Heat index is only calculated when temperature is 80°F / 27°C or above.

WIND

To select wind display mode:
Press wind area to toggle between:

• Gust
• Average

Press UNIT to select unit: knots / kph / mph / m/s.
The wind level is shown by a series of icons:

Lost sensor	Light	Moderate	Strong	Storm
	0-8 mph (3-13 km/h)	9-25 mph (14-41 km/h)	26-54 mph (42-87 km/h)	>55 mph (>88 km/h)

MOON PHASE

1. Press clock area to activate.
2. Press SET repeatedly to display Year / Calendar date.
3. Press UP / DWN to view moon phase for specific dates.

BAR CHART

To select chart display mode:
Press bar chart area to toggle between these chart displays:

• Barometer
• Rain
• UV

ALARM

Weather alarms are used to alert you of certain weather conditions. Once activated, the alarm will turn off when a certain criterion is met.

Area	Type of alarm
Barometer	Barometer	HI
Rain	Rain rate	HI
UV	UV	HI
Temperature	Current Temperature	HI
		LO
	Heat Index	HI
Humidity	Current Humidity	HI
		LO
	Dew Point	HI
		LO
Clock	Daily Alarm
Wind	Gust Wind Speed	HI
	Low Wind Chill	LO

To set the alarm:

1. Press desired area to activate.
2. Press AL to display Time and HI / LO alarm.
3. Press and hold AL
4. Press UP / DWN to set the desired values.
5. Press
   • AL to confirm and continue to next setting OR
   • touch anywhere on the screen (except tool bar / weather forecast area) to confirm and exit.

To enable / disable alarms:

1. Press desired area to activate.
2. Press AL to display set Time and HI / LO alarm.
3. Press AL ON/OFF to turn alarm ON / OFF.
   "- -" indicates alarm is not set / disabled.

NOTE
Clock alarm sound is different from weather alarms to allow for easy differentiation by user. To silence any alarm: Press anywhere on the screen.
NOTE
will continue flashing, despite silenced alarm, for at least 2 minutes or until condition ceases.
NOTE
When alarm is on, the channel of triggered alarm will be displayed.