Holmes HAWF2021TG, HAWF2021 - Twin Window Fan Manual

FEATURES - OPERATIONS

INSTALLATION INSTRUCTIONS

Carefully unpack all contents of carton.

NOTE: MAKE SURE YOU REMOVE ALL CONTENTS FROMTHE PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR PARTS THAT COULD BE REQUIRED TO OPERATE YOUR FAN.

• The window fan comes fully assembled and is ready for immediate installation.
• Before installation, familiarize yourself with the built in 7 inches (17cm) extender on the right side of the fan, and the additional 4.25 inches (10cm) extender which attach to the left side of the fan housing (see Figure 1).
  

NOTE: WE RECOMMEND KEEPING YOUR WINDOW SCREEN IN PLACE.

This window fan has been designed to fit double-hung windows with minimum openings of 22 inches (55cm) wide and 10 inches (25cm) high.

1. Align the Window Fan horizontally in the window and the Built-In Extender Panel to the right.
2. With the window open take an accurate measurement of the opening where the unit will be placed.
3. Match your window measurement with the INSTALLATION GUIDE.
4. Once you have attached the extender panel(s) (if needed), set the fan in the window. You will complete installation with built-in extender. Pull out both clips on right side of the fan then pull out the built-in extender.
5. Carefully close the window onto the top of the fan so that the bottom edge of the window rests behind top line of fan housing. This helps keep the fan in place.

For slider windows (will fit windows 10 inches/25cm wide and 36 inches/91cm high)

In a slider window, the control must face inward, towards the window. The 7 inches (17cm) built-in extender will be positioned on top. Prior to installing unit in window, measure the height and adjust the upper extender for a snug fit.

NOTE: In some slider windows you may need to remove the screen.

INSTALLATION GUIDE

For 22 inches (55cm) to 29 inches (73cm):
Use up to 7 inches (17cm) of right side, pull out extender panel.

For 29 inches (73cm) to 33.25 inches (83cm):
Use one 4.25 inches (10cm) extender panel on the left side. Adjust the pull out extender on the right side for a tight fit (from 0.5 inches (1cm) to 7 inches (17cm) ).

Larger than 33.25 inches (83cm):
Additional extender panels will be required (See Window Fan Accessory Section).

OPERATING INSTRUCTIONS

• Make sure rotary switch is in the OFF position.
• Plug into 120V AC electric outlet.
• To use in EXHAUST mode, manually turn the unit around in the window. (Controls can be operated from both sides.)
• To start the unit, turn the rotary switch(C) to desired speed (high or low).

BE SURE FAN IS SECURELY INSTALLED IN YOUR WINDOW AT ALL TIMES. DO NOT LEAN OR PUSH ON FAN WHILE IT IS IN THE WINDOW.

CLEANING/MAINTENANCE

INSTRUCTIONS

Follow these instructions to correctly and safely care for your window fan. Please remember:

REPLACEABLE FUSE
If your (5 Amp, 125 Volt) replaceable fuse blows, please order a new fuse at 1-800-546-5637. Follow the below instructions to replace the fuse on the plug.

User Servicing Instructions

1. Unplug your fan. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
2. Open fuse cover, located on the top of the plug, by using your thumb or a flathead screwdriver to slide the cover down towards the prongs.
   Note: Ensure that fuse cover is completely open before attempting to remove fuse.
3. Remove fuse carefully by using a small screwdriver to pry the fuse out of the compartment by the metal ends of the fuse (see Figure 3).
   
4. Place plug on a solid, flat surface. Insert new 5 Amp, 125 Volt fuse into fuse compartment and use a small screwdriver to secure the metal ends of the fuse into the compartment.
   
   Risk of fire. Replace fuse only with 5 Amp, 125 Volt fuse.
5. Slide fuse cover closed completely. If fuse cover is difficult to close, make sure fuse is secured in place completely by pressing down on metal ends of the fuse.
6. Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged.

FAN CLEANING

• Always unplug the fan before cleaning or disassembling.
• Do not allow water to drip on or enter into the fan motor housing.
• Be sure to use a soft cloth moistened with mild soap solution.
• Do not use any of the following as a cleaner: gasoline, thinner, benzene.

Fan blade and Front Grill Cleaning

1. Make sure the fan is unplugged.
2. Using a Phillips head screwdriver, remove the screws that hold the front and rear grills together. Carefully separate the front and the rear grills from the end opposite the built in extender. Do not completely detach the grills as this may damage the extender clips. Separate only enough to gain access to the blades with one hand.
3. Clean blades and grills with a soft, moist cloth (see above).
4. Securely fasten the grills together.

STORAGE / FAN ACCESSORIES

FAN STORAGE

For all window fans, and fans that come already assembled.

• It is important to keep it in a safe, dry location.
• We recommend using the original (or appropriately
• Please remember to protect the fan from dust or moisture.

WINDOW FAN ACCESSORIES

Window Fan Extender Panel

To order please go to www.holmesproducts.com or call 1-800-546-5637

If you have any questions regarding your product or would like to learn more about other Holmes ® products, please contact our Consumer Service Department at 1-800-546-5637 or visit our website at www.holmesproducts.com.

© 2011 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All Rights Reserved.
Distributed by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431.