Troubleshooting Fault Codes - Viking Professional 200 Series Use & Care Manual

Troubleshooting/Fault Codes
FLASH
Pots/ Normal
Pans Wash
1 1 1 1
1 1 2 2
1 1 3 3
1 1 4 4
1 1 5 5
2 2 1 1
2 2 2 2
2 2 3 3
2 2 4 4
2 2 5 5
3 3 1 1
3 3 3 3
5 5 5 5
S S e e e e N N o o t t e e A A
S S e e e e N N o o t t e e B B
N N o o t t e e A A - - Both lights flash continuously.
N N o o t t e e B B - - All lights, except START and RUN (select models), flash continuously.
N N o o t t e e C C - - To reset unit, press and hold the "START" button for four seconds.
N N o o t t e e D D - - Numbers listed indicate the times the lights will flash when a specific
error is detected (example: For a drain error, the POTS/PANS light will flash once
and the NORMAL WASH light will flash 5 times).
All manuals and user guides at all-guides.com
FAULT
Pan Flood Sensor Disconnect
Motor Control Status Error
Motor Control Comms Error
Diverter Timeout
Drain Error
Huba Disconnect Error
Fill Timeout
Low Level Sensor Error
High Level Error
Level Sensor Error
UI-MC Comm Error
Drain Pump Error
Internal Error
Pan Flood
Power Loss
34
ACTION
Reset Unit and try again. If problem persists, contact service.
Reset Unit and try again. If problem persists, contact service.
Reset Unit and try again. If problem persists, contact service.
Reset Unit and try again. If problem persists, contact service.
1. Turn water on at sink and run garbage disposal to verify that sink is not clogged.
2. Verify that dishwasher drain hose is not clogged or kinked.
3. If draining into disposal, verify that plug has been removed from disposal.
4. Verify that drain hose has high loop, per installation guide.
5. Verify that dishwasher is level front to back and side to side.
6. Verify filters are not clogged.
Reset Unit and try again. If problem persists, contact service.
Reset Unit and try again. If problem persists, contact service.
1. Verify water supply to dishwasher is turned on.
2. Verify that fill line is not kinked.
3. Verify that dishwasher is level front to back and side to side.
4. Turn water on at sink and verify there has not been a decrease in water pressure.
Reset Unit and try again. If problem persists, contact service.
1. Verify that no dishes have turned over and are holding a significant amount of water.
2. Verify that drain hose has high loop, per installation guide.
Reset Unit and try again. If problem persists, contact service.
1. Verify items in rack are properly retained so that they can not turn over.
Reset Unit and try again. If problem persists, contact service.
1. Verify that dishwasher is level front to back and side to side.
2. Verify that drain hose has high loop, per installation guide.
Reset Unit and try again. If problem persists, contact service.
Reset Unit and try again. If problem persists, contact service.
Reset Unit and try again. If problem persists, contact service.
Reset Unit and try again. If problem persists, contact service.
Reset Unit and try again. If problem persists, contact service.
Reset Unit and try again. If problem persists, contact service.
T T u u r r n n i i n n g g A A u u d d i i b b l l e e S S o o u u n n d d O O n n a a n n d d O O f f f f : :
To turn off, press Rinse/Hold button for 10 seconds. The beep stops and the
Rinse/Hold LED will flash 2 times. (Note: The audible sound cannot be disabled
for error messages.) To turn on, repeat above instructions. The audible sound
beeps 2 times and the Rinse/Hold LED flashes 2 times to identify that it is on.
(Note: The LED will flash in sync with the audible sound.)
35