Related Manuals for Hunter Visalia
Summary of Contents for Hunter Visalia
- Page 1 Visalia Installation Manual Model: 50595 Quartz Grey 53430 Fresh White Fan weight ±2 lbs: 20.9 lbs (9.5 kg) ©2020 Hunter Fan Co. PG3856 r021020...
- Page 2 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. c.2 - Use only Hunter replacement parts. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 3 We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those Hunter Pro Tip: parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component.
-
Page 4: Choosing The Right Installation Location
A little more information on Angled Mounting: For optimum performance and appearance, a longer downrod should be used with your Hunter ceiling fan when installing on high or angled ceiling. If your ceiling is angled greater than 34° you will also need an Angled Mounting Kit. -
Page 5: Installing The Ceiling Bracket
You have two options for installation. Pick which one works best for your location. Remove any existing Hunter Pro Tip: bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box. The machine screws are the ones that came with your outlet box. -
Page 6: Hanging The Fan
1886 Hanging the Fan NOTICE To prevent damage to fan, ALWAYS lift holding either the fan housing or the downrod. Place the downrod ball into the slot in the ceiling bracket. Progress Check: Your fan should look like this. Ceiling Bracket Downrod Hanging Fan Wiring... -
Page 7: Wiring The Fan
If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. You are going to need these: Hunter Pro Tip: Here is how to connect the wires: 4 Wire Nuts (these are in the... -
Page 8: Installing The Canopy
Canopy Screw Lift the canopy into place so that the screw holes are aligned. NOTICE Hunter Pro Tip: Let the tool do the work! If screw holes do not align A magnetic screwdriver will properly then rotate the canopy 180 degrees. -
Page 9: Installing The Blades
1886 Installing the Blades: Put the blade washers, found in the hardware bag, onto the blade screws, found in the hardware bag. Then install the blade screws to secure each blade to a blade iron. Repeat x4 Blade Screw IMPORTANT Washer NOTE: Follow the instructions on the blade. -
Page 10: Assembling The Light Kit
1886 Assembling the LIght Kit 1 of 6 2 of 6 Light Kit Screw Light Kit Screw Feed the wire plug through the center hole of the upper switch Partially install two light kit Insert the third screw, found in the housing, then wrap keyhole assembly screws, found in the hardware bag, into place and... -
Page 11: Preparing The Remote
1886 Preparing the Remote The remote control is NOTICE already paired for use. For your convenience, a remote • Always purchase the correct size and grade of function card is packed in battery most suitable for the intended use. with your remote. •... -
Page 12: Troubleshooting
Hunter instructions, accidental damage caused by the fan owner or related parties, Please do not ship your fan or any fan parts to Hunter. Delivery will be refused. modifications to the fan, improper or incorrectly performed maintenance or repair,... - Page 13 1886 Downrod If you need a different downrod length follow these steps: Follow steps 1-5 to remove standard downrod pipe Follow steps 6-10 to reassemble with new downrod WARNING FAN FALL HAZARD To prevent SERIOUS INJURY or DEATH: • ALWAYS follow the downrod assembly instructions exactly.