Sear Station ® Troubleshooting; Rotisserie Troubleshooting; Grill Light Troubleshooting - Weber Summit E-670 Owner's Manual

PROBLEM
Burners burn with a yellow or orange flame, in
conjunction with the smell of gas. (This is normal for
the burner lighting tube.)
Sear Station burner does not light.
®
General Symptoms:
Burner does not light.
OR
Burner has a small flickering flame.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site.
Log onto www.weber.com.
PROBLEM
Rotisserie burner does not light.
General Symptoms:
Burner does not light.
OR
Burner has a small, flickering flame.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site.
Log onto www.weber.com.
PROBLEMS
Grill light does not turn on.
Grill light turned off and will not turn back on.
Grill light does not turn off.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site.
Log onto www.weber.com.
32
SEAR STATION TROUBLESHOOTING
®
CHECK
Inspect spider/insect screens for possible obstructions.
(Blockage of holes.)
Did you ignite the two adjacent main burners? Refer to
"SEAR STATION IGNITION & USAGE" for safe lighting
®
procedure.
Does burner light with a match?
Does the igniter work? Do you see a spark when you
repeatedly use the snap igniter?
The excess flow safety device, which is part of the grill to
tank connection, may have been activated.

ROTISSERIE TROUBLESHOOTING

CHECK
Did you hold the burner control knob in and hold in for 20
seconds after burner ignited?
Did you wait to see the entire ceramic surface become
alight before counting 20 seconds?
Did you repeatedly use the snap ignition until the burner
ignited?
Does the igniter work? Do you see a spark when you
repeatedly use the snap igniter?
The excess flow safety device, which is part of the grill to
tank connection, may have been activated.

GRILL LIGHT TROUBLESHOOTING

The grill light will activate only when lid is open. Lift the lid to the open position and press the AWAKE button.
Install new batteries. When installing new batteries (alkaline only), confirm that each battery's plastic wrapping has
been removed. Verify that the batteries are in good condition and have been installed correctly. Refer to "MAINTAINING
THE GRILL LIGHT."
The light is programmed to turn off automatically after 30 minutes of inactivity. To reactivate the light, make sure lid is
open and press the AWAKE button. Refer to "MAINTAINING THE GRILL LIGHT."
The grill light is equipped with a tilt sensor. The tilt sensor turns the light ON when grill lid is opened and OFF when
the grill lid is closed.
NOTE: The AWAKE button will not turn the grill light off. To turn the light off, put the lid in the closed position.
SOLUTION
Clean spider/insect screens.
Refer to "ANNUAL MAINTENANCE."
Verify adjacent main burner ignition by visual inspection
of a flame.
m WARNING: If ignition does not occur in
five seconds, turn burner control OFF,
wait five minutes to let the gas clear
before you try again.
If you can light burner with a match, then check the
Crossover Channel on the sear burner.
®
Refer to "MAINTENANCE" for burner removal and
cleaning procedure.
Try manually lighting the burner. Refer to "SEAR
STATION IGNITION & USAGE." Call Customer Service.
®
To reset the excess flow safety device, turn all burner
control knobs and the tank valve to OFF. Disconnect the
regulator from the tank. Turn burner control knobs to
START/HI. Wait at least one minute. Turn burner control
knobs to OFF. Reconnect the regulator to the tank. Turn
tank valve on slowly. Refer to "MAIN BURNER IGNITION."
SOLUTION
Try to relight burner by holding burner control knob in;
continue holding in until 20 seconds after burner has
ignited.
When relighting burner by holding burner control knob
in, wait to see the entire ceramic surface become alight
before counting 20 seconds.
After waiting five minutes for gas to clear, try using the
snap igniter repeatedly until the burner ignites. Refer to
"ROTISSERIE BURNER IGNITION & USAGE."
Try manually lighting the burner. Refer to "ROTISSERIE
BURNER MANUAL IGNITION." Call Customer Service.
To reset the excess flow safety device, turn all burner
control knobs and the tank valve to OFF. Disconnect the
regulator from the tank. Turn burner control knobs to
START/HI. Wait at least one minute. Turn burner control
knobs to OFF. Reconnect the regulator to the tank. Turn
tank valve on slowly. Refer to "MAIN BURNER IGNITION."
SOLUTIONS