Table of Contents
Advertisement
For example, to fi nd out which code is assigned to your TV:
For example, to fi nd out which code is assigned to your TV:
1.
1.
Press TV once.
Press TV once.
2.
2.
Press and hold SET until the red LED blinks twice; then release.
Press and hold SET until the red LED blinks twice; then release.
3.
3.
Enter 9-9-0. The LED blinks twice.
Enter 9-9-0. The LED blinks twice.
4.
4.
To view the code for the fi rst digit, press 1. Count the LED blinks (for example, three blinks = 3), and write
To view the code for the fi rst digit, press 1. Count the LED blinks (for example, three blinks = 3), and write
down the number in the appropriate code listing in step 8 under "Programming a Device".
down the number in the appropriate code listing in step 8 under "Programming a Device".
•
•
NOTE: If a code digit is 0, the LED does not blink.
NOTE: If a code digit is 0, the LED does not blink.
5.
5.
Repeat step 4 for the four remaining digits, using 2 for the second digit, 3 for the third digit, 4 for the fourth
Repeat step 4 for the four remaining digits, using 2 for the second digit, 3 for the third digit, 4 for the fourth
digit, and 5 for the fi fth digit.
digit, and 5 for the fi fth digit.
Changing Volume Lock
Changing Volume Lock
The remote comes preset to allow independent volume control of each selected device (Global Volume Unlock).
The remote comes preset to allow independent volume control of each selected device (Global Volume Unlock).
However, you may change the Volume Lock setting to Global Volume Lock so that one device's volume will
However, you may change the Volume Lock setting to Global Volume Lock so that one device's volume will
control volume in all other modes. After that, you can perform Individual Volume Unlock on a selected device to
control volume in all other modes. After that, you can perform Individual Volume Unlock on a selected device to
set its volume control for independent operation or Global Volume Unlock to remove all volume locking.
set its volume control for independent operation or Global Volume Unlock to remove all volume locking.
Locking Volume Control to One Mode (Global Volume Lock)
Locking Volume Control to One Mode (Global Volume Lock)
1.
1.
Press and hold SET until the red LED blinks twice; then release.
Press and hold SET until the red LED blinks twice; then release.
2.
2.
Enter 9-9-3 and then press the mode key for the device you want to control volume (for example, TV).
Enter 9-9-3 and then press the mode key for the device you want to control volume (for example, TV).
The LED blinks twice. Now when you press VOL+, VOL-, or Mute, the selected device (for example,
The LED blinks twice. Now when you press VOL+, VOL-, or Mute, the selected device (for example,
TV) will control the volume regardless of the current mode.
TV) will control the volume regardless of the current mode.
Unlocking All Volume Control (Restoring Global Unlock)
Unlocking All Volume Control (Restoring Global Unlock)
1.
1.
Press and hold SET until the red LED blinks twice; then release.
Press and hold SET until the red LED blinks twice; then release.
2. Enter 9-9-3 and then press VOL+. The LED blinks four times. Volume is now
2. Enter 9-9-3 and then press VOL+. The LED blinks four times. Volume is now
independently controlled for all programmed devices.
independently controlled for all programmed devices.
Unlocking a Single Device's Volume Control
Unlocking a Single Device's Volume Control
1.
1.
Press a device key (TV, VCR/DVD, CBL/ SAT, or AUX).
Press a device key (TV, VCR/DVD, CBL/ SAT, or AUX).
2.
2.
Press and hold SET until the red LED blinks twice; then release.
Press and hold SET until the red LED blinks twice; then release.
3. Enter 9-9-3 and then press VOL-. The LED blinks four times. Volume is now
3. Enter 9-9-3 and then press VOL-. The LED blinks four times. Volume is now
independently controlled for the selected devices.
independently controlled for the selected devices.
Troubleshooting
Troubleshooting
PROBLEM: LED does not blink when you press a key.
PROBLEM: LED does not blink when you press a key.
SOLUTION: Replace battery with new AA size battery.
SOLUTION: Replace battery with new AA size battery.
PROBLEM: LED blinks when you press a key, but device does not respond.
PROBLEM: LED blinks when you press a key, but device does not respond.
SOLUTION: Make sure the remote is aimed at your device and is not more than 15 feet away.
SOLUTION: Make sure the remote is aimed at your device and is not more than 15 feet away.
PROBLEM: LED blinks one long blink.
PROBLEM: LED blinks one long blink.
SOLUTION: An entry error has occurred (for example, wrong key). Try entry sequence again.
SOLUTION: An entry error has occurred (for example, wrong key). Try entry sequence again.
PROBLEM: Remote does not control devices or commands are not working properly.
PROBLEM: Remote does not control devices or commands are not working properly.
SOLUTION: Try all listed codes for the device. Make sure the device operates with an infrared remote control.
SOLUTION: Try all listed codes for the device. Make sure the device operates with an infrared remote control.
PROBLEM: CH+, CH-, and LAST do not work for your RCA TV.
PROBLEM: CH+, CH-, and LAST do not work for your RCA TV.
SOLUTION: Due to RCA design from 1983 to 1987, only the original remote control will operate these functions.
SOLUTION: Due to RCA design from 1983 to 1987, only the original remote control will operate these functions.
PROBLEM: No volume on a device.
PROBLEM: No volume on a device.
SOLUTION: See "Changing Volume Lock".
SOLUTION: See "Changing Volume Lock".
PROBLEM: Channels do not change properly.
PROBLEM: Channels do not change properly.
SOLUTION: If the original remote control required you to press Enter to change channels, press Enter on this
SOLUTION: If the original remote control required you to press Enter to change channels, press Enter on this
remote after entering the channel number.
remote after entering the channel number.
46
Hide quick links:
Advertisement
Table of Contents
