Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Genelec 4410A
Summary of Contents for Genelec 4410A
- Page 1 4410A Operating Manual...
-
Page 2: General Description
The 4410A is manufactured using certified sustainable methods. All essential parts of the loudspeaker can be recycled. The 4410A is available in black or white colours. It is compatible with Genelec’s extensive range of mounting accessories for floor, ceiling, wall, or truss mounting. -
Page 3: Packing Content
The 4410A accepts AES67/ST2110 and Dante audio-over-IP streams. The streams are set up with Dante Controller or Dante Domain Manager software. Each 4410A supports reproduction of one or the sum of two audio input channels. The stream audio sample rate can range from 32-96 kHz, with 16-24 bit resolution. - Page 4 The accessories can come with instructions on the proper methods of installation. THREADS FOR WALL AND CEILING MOUNTS POWER SWITCH 4410A 292 4410S SMART IP SPEAKER ETHERNET PoE+ AES67 ETHERNET PORT MAC ADDRESS Figure 2. Connectors and controls in the 4410A rear panel.
-
Page 5: Connecting Loudspeakers
CONNECTING LOUDSPEAKERS To get started, connect an Ethernet cable from the PoE+ output of an IP switch to the 4410A Ethernet port. Use at least CAT5 cable or better. Press the power switch to power up the loudspeaker. To create a working system, you will need •... - Page 6 PoE+ standard but also works with the lower power PoE standard. While the 4410A also works with the lower PoE power, the maximum SPL is affected by the PoE power available. Please consult the specification table in this manual for details.
- Page 7 API command or in response to IP audio stream. The power consumption in of a 4410A in standby mode is 3 W. To save more power, the PoE+ power supply in the Ethernet switch or PoE injector can be turned off. However, the...
-
Page 8: Network Structure
The 4410A can select one audio channel or a sum of two channels in a stream. The AES67 compatibility mode must turned ON to enable reception of AES67 or ST2110 streams. -
Page 9: Zone Settings
Interface (API) inside the loudspeaker used with house automation systems for end-user control. Download Smart IP Manager at https://www.genelec.com/smart-ip-manager and follow screen instructions to install. For detailed use of the Genelec Smart IP manager software, please refer to the Smart IP Manager operating manual. Zone settings A zone is a collection of loudspeakers working as a system. - Page 10 Figure 6. Controlling the zone with Smart IP Manager software. Editing acoustic settings The frequency response of the 4410A can be compensated for the room’s acoustical influences by editing the settings in the Acoustics tab in the Genelec Smart IP Manager. Acoustical calibration settings are specific to each loudspeaker.
-
Page 11: Factory Settings
Set stream again to resume normal streaming operation. To reset a 4410A to factory settings, press the power button for more than 10 seconds. The loudspeaker indicates that the reset process starts. Then, you can release the power button but do not disconnect power supplied by the Ethernet cable until the reset process is complete. -
Page 12: Maintenance
MAINTENANCE There are no user-serviceable parts in the loudspeaker. Maintenance or repair of the 4410A must only be done by Genelec authorised service personnel. This is particularly important to maintain. SAFETY CONSIDERATIONS The 4410A has been designed in accordance with international safety standards. -
Page 13: Specifications
The stated values are typical for music and speech signals. Maximum long-term output level can be further limited by loudspeaker system protection. Genelec recommends using PoE+ whenever possible. Using lower-power PoE can limit short-term maximum and long-term maximum, depending on the characteristics of the signal being reproduced. - Page 14 INPUT / CROSSOVER SECTION Ethernet connection 100BASE-TX 1 x RJ45 Nominal SPL with 0 dBFS digital audio input at 130 dB SPL maximum sensitivity Audio-over-IP streaming formats AES67, ST2110-30, Dante Crossover frequency, bass/treble 2.9 kHz Number of user-adjustable filters User selectable filters, choice of function for each parametric notch user-adjustable filter high frq.
- Page 15 Figure 8. Frequency responses on the horizontal plane. Off-axis angle indicated in degrees. 4410A horizontal plane, normalized with on−axis −3 −6 −9 −12 −15 −30 −15 −45 −60 −18 −75 −90 −21 Frequency (Hz) Figure 9. Horizontal directivity plot of the 4410A. Colour bar indicates dB level.
- Page 16 −45 −60 −18 −75 −90 −21 Frequency (Hz) Figure 10. Vertical directivity plots of the 4410A. Colour bar indicates dB level. 4410A directivity index Frequency (Hz) 4410A power response Frequency (Hz) Figure 11. Directivity index (top) and power response (bottom).
- Page 17 4410A Latency at zero 2.3 ms −5 Frequency (Hz) Figure 12. System delay from the audio-over-IP stream input. 4410A −100 Frequency (Hz) Figure 13. Phase response.
- Page 18 Phone +86 400 700 1978 Email genelec.china@genelec.com In Japan Genelec Japan Inc 2-22-21 Akasaka Minato-ku JP-107-0052 Tokyo Japan Phone +81 3 6441 0591 Email genelec.japan@genelec.com www.genelec.com Genelec Document D0178R001. Copyright Genelec Oy 9.2021. All data subject to change without prior notice...