Table of Contents
Advertisement
Initialization (reset)
Initialize (reset) the WLAN adapter in the following situations:
• Changing the access point
• Disposing of this product
• Transferring this product to a third party
Unregister the air conditioner
Unregister the air conditioner by using the mobile app. (Refer to the
operation manual of the mobile app for details.)
Initialization of the WLAN adapter
NOTE: If you do not press any buttons of the remote controller for
60 seconds, the remote controller display will return to the
original display.
1. If the air conditioner is operating, press
to stop the operation.
2. Press and hold
on the remote
controller for more than 5 seconds.
will be displayed on the remote controller
display.
3. Select
using
controller.
4. Press
.
on the remote controller display will blink.
5. Press
.
[
] indicator on the indoor unit will turn off after blinking fast.
To continue use
If you or a third party wishes to continue the use of the WLAN adapter,
follow the procedures in "Air conditioner registration (pairing of WLAN
adapter)" to reconnect to a diff erent access point.
NOTE: WLAN setup is not possible if the previous owner did not
unregister or initialize the WLAN adapter. In this case, contact
your authorized service personnel.
Removing WLAN adapter
CAUTION
• Be sure to turn off the power supply of the air
conditioner when installing or removing the WLAN
adapter to avoid the risk of electric shock.
• Do not put fi ngers, sticks, etc., in the connection part
of the WLAN adapter and the connection slot of the
indoor unit. Otherwise, electric shock or damage to
this product may occur.
• Do not stand on an unstable platform when installing
or removing the WLAN adapter to avoid injury.
1. Be sure to turn the air conditioner off and disconnect all the
power supplies.
2. Open the intake grille.
on the remote
3. Open the WLAN adapter cover until it snaps.
4. Remove the WLAN adapter from the connection slot of the
indoor unit in the direction as shown in the fi gure.
5. Close the WLAN adapter cover and the intake grille.
10. SETTINGS ON INSTALLATION
10.1. Remote controller custom code setting
By setting custom codes of the indoor unit and the remote controller,
you can specify the air conditioner which the remote controller controls.
When two or more air conditioners are in the room, and you wish to
operate them separately, set the custom code (4 selections possible).
NOTE: If custom codes are diff erent between the indoor unit and the
remote controller, the indoor unit cannot receive a signal from
the remote controller.
How to set the remote controller custom code
1. Press
until only the clock is displayed on the remote
controller display.
2. Press and hold
for more than 5 seconds.
The current custom code will be displayed (initially
set to A).
3. Press
to change the custom code
between A ( ) ↔ B ( ) ↔ C (
* Match the custom code on the display to the air conditioner
custom code.
4. Press
again.
The custom code will be set.
The display will return to the clock display.
• To change the air conditioner custom code, contact an authorized
service personnel (initially set to A).
• If you do not press any buttons for 30 seconds after the custom
code is displayed, the display returns to the clock display. In this
case, repeat the setting from step 2.
• Depending on the remote controller, the custom code may return
to A when replacing the batteries. In this case, reset the custom
code as necessary. If you do not know the air conditioner custom
code, try each code until you fi nd the code which operates the air
conditioner.
11. CLEANING AND CARE
CAUTION
• Before cleaning this product, be sure to turn it off and
disconnect all the power supply.
• Before starting operation, make sure that the intake
grille has been shut completely. Incomplete closing
of the intake grille might have an eff ect on the proper
working or performance of the air conditioner.
• If the fi lter cleaning involves high-place work, consult
the authorized service personnel.
) ↔ D ( ).
En-10
Advertisement
Table of Contents
