Planar PT1510MX Quick Start Manual

PT1510MX/PT1710MX
15" PT1510MX AND 17" PT1710MX
Thank you for choosing Planar's 15" PT1510MX or
QUICK START GUIDE
17" PT1710MX resistive touchscreen monitor.
Customer Service:
To view online documentation and frequently
asked questions, or to send an email to our
technical support staff , please visit:
http://www.planar.com/support or call
1-866-PLANAR1 (1-866-752-6271) in the United
States or +1 503-748-5799 outside the United
States.
To receive advanced notifi cation of product
updates, please register your monitor at
www.planar.com/support.
Planar has nearly 25 years experience delivering
specialty display solutions for the most demanding
applications. Each PT touch LCD monitor comes
standard with our 3-Year Customer First™ Warranty
featuring FREE 2-Day Advance Replacement
including prepaid shipping both ways.
Monitor Set-up
1. If it is necessary, clean the front surface of
If you're using the USB connection follow the
the display by using clean, compressed air
instructions below:
or by using only a clean, dry, soft cloth.
2. Connect the video and power cables.
3. Read the Touch Set-up section prior to 1. Be sure that the USB cable is not connected
powering up the computer. to the PC.
2. Load the CD-Rom.
Touchscreen Set-up - 3. Follow the step-by-step instructions as found
in the Touch Screen Driver Installation
Please note: The PT1510MX and PT1710MX
Manual located on the CD.
are available with both RS-232 and USB
4. Reconnect the USB cable between the
connections. If you're using the RS-232
computer and monitor prior to use.
connection follow the instructions below:
5. If the touch screen isn't active, simply reboot
your system.
1. Be sure that the RS-232 cable is disconnected
from the computer.
PLEASE NOTE! Don't plug in both the RS-232
2. Power on the computer
and USB cables! Doing so may cause a driver
3. Load the Touch Screen Driver CD
confl ict, making your touch screen inoperable.
4. Follow the step-by-step instructions as
found in the Touch Screen Driver Installation
Manual located on the CD.
5. Reconnect the RS-232 cable between the
computer and monitor prior to use.
Set-up Diagram Package Overview
1. Power Cord
Contents -
2. VGA Cable
3. Audio-In Cable
4. RS-232 Cable
5. USB Cable
5
4
1
2
3
PT1510MX
5
4
3
1 The test results show that this device meets the FCC rules. Refer to the product operation manual for FCC classifi cation found at: http://www.planar.
2
com/support. Those limits are set to protect residential areas from the devices with harmful emission. This device will produce, use and radiate radio fre-
quency energy. In addition, failure to follow the user's manual to install or use this device might produce harmful interference with radio communication.
PT1710MX
Notwithstanding the foregoing, it does not guarantee that this type of harmful interference does not occur in some special installations. The interference
caused by this device to the reception of radio or television signals may be verifi ed by turning it on and off . Any changes or modifi cations to this TFT LCD
would void the user's authority to operate this device.
Warning! Don't plug in both the RS-232 and USB cables! This will
cause your touch screen not to work due to driver confl ict.
Importand Recycle Instruction -
LCD Lamp(s) inside this
product contain mercury.
This product may contain other
electronic waste that can be
hazardous if not disposed of
LCD Display Power Adapter Power Cord
properly. Recycle or dispose in
accordance with local, state, or
federal Laws. For more information,
VGA Signal Cable Audio-in Cable USB Cable
contact the Electronic Industries
Alliance at WWW.EIAE.ORG. For
lamp specifi c disposal information
check WWW.LAMPRECYCLE.ORG.
RS-232 Cable Landing Strip Touchscreen Driver
Installation CD-ROM
User's Guide
020-0488-00B
36.59904G004 Ver. A