Page 3
Important Recycle Instructions: Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG.
VESA Mount your monitor………………………………………………..9 Start Your Installation…………………………………………………….10 User Controls Front Panel Controls ................ 14 How to Use the OSD Menus ............15 On-Screen Display Menus For PT1510MX Product ......16 Appendices Troubleshooting ................17 Warning Signal ................. 18 Product Dimensions ................. 19 Compatibility Modes .................
Usage Notice - To prevent the risk of fire or shock hazards, do not Warning expose this product to rain or moisture. - Please do not open or disassemble the product as Warning this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit.
Introduction About Planar’s PT1510MX The PT1510MX is a 15” flat panel screen with an active matrix, thin-film transistor (TFT) liquid crystal display (LCD). Features include: Direct Analog signal input Active matrix TFT LCD technology 1024x768 XGA resolution 15” diagonal screen size 31.5 ~ 60 kHz horizontal scan...
Touch Screen for PT1510MX Analog 5-wire resistive touch screen for finger and stylus input Surface: Anti-glare treatment Interface: Dual RS-232 Serial/USB controller Durability: 35 million touches at a single point Hardness of surface: 2H MIN (As provided in JIS K 5400) Operating force: 0.10~1.96N(10g~200g when using a silicon tipped pen...
Page 12
Kensington Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products. The Kensington lock is not included.
VESA Mount Your Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface Standard which defines a physical mounting interface for flat panel monitors, and corresponding standards for flat panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your monitor.
Start Your Installation Remove the Back Cover Please follow these instructions to remove the cover on the back panel of the LCD so that you can connect the cables in “Connector Ports B.” 1. To remove the back cover, follow the arrows in Figure A and press with both your thumbs.
Page 15
Connecting the Display (Figure 11.1, 11.2) To setup this display, please refer to the following figure and procedures. 1. Be sure all equipment is turned off. 2. Connect the DC power cord to the power connector on the monitor; plug one end of the AC power cord into the power adapter, and the other end into an electrical outlet (11.1 ).
User Controls Front Panel Controls Control Function No / Icon MENU Menu button Display the OSD menus Select – To select the adjustment items from OSD menus. SELECT/AUTO Select/Auto Auto – To activate the “Auto Adjustment” function to obtain an optimum image. 1.
How to Use the OSD Menus Press the "MENU" button to pop up the “on-screen menu” and to select among the four Main Menus. 2. Choose the adjustment items by pressing the “Select/Auto” button. 3. Adjust the value of the adjustment items by pressing the “ ”or “ “ button. 2.
On-Screen Display Menus for the PT1510MX Product Main Menu Menu Level 2 Function Description Remark Choose this function to adjust the Default 30 Brightness brightness of the image. Choose this function to adjust the Default 40 Contrast contrast of the image.
Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen. Check that all the I/O and power connectors are correctly and well connected as described in the “Installation”...
LCD display cannot receive a clean signal from the computer graphics card. There may be two sources for this problem. Please check the cable connections or contact Planar for more information. No Signal This message means that the LCD Display has been powered on but it cannot receive any signal from the computer graphics card.
Compatibility Modes V. Frequency H. Frequency Mode Resolution (Hz) (kHz) IBM VGA 640 x 350 31.5 640 x 400 IBM VGA 31.5 720 x 400 IBM VGA 31.5 640 x 480 IBM VGA 31.5 VESA VGA 640 x 480 37.9 VESA VGA 640 x 480 37.5...
Touch Screen Driver Installation The PT1510MX is available with both RS-232 and USB connections. The PT1510MX is Microsoft® Windows® HID (Human Interface Device) compatible if you use the USB touch screen interface. No additional software driver is required for general operation of the touch screen. A calibration tool can be installed for improved touch position accuracy.
Page 26
PT1510MX Optional Resistive Calibration Tool Install: If you would like to use the Optional Resistive Calibration Tool, follow the instructions below: 1. Open the CD-Rom. 2. Select the Monitor Size and then Model Name 3. Click on the “Load Utility” button that appears to the right of the Model Name.
Page 27
® If you are using a PC running Windows Vista, XP or 2000 operating system, follow the instructions below. Using the RS232 connection: 1. Be sure that RS232 cable is connected from the computer. 2. Power on the computer. 3. Load the touch screen driver CD. 4.
Product Registration and Technical Support Register Your Planar Products Today Thank you for choosing Planar. To assure you receive all the benefits of your Planar product and services, register your Planar product today. Visit our website at http://www.planar.com/support/product_registration.html. Cables, Replacement Lamps, Accessories...
Page 44
防 盗 锁 槽 防 盗 锁 槽 Kensington 防 盗 锁 槽 防 盗 锁 槽 Kensington Kensington 防 盗 锁 防 盗 锁 槽 槽 槽 槽 防 盗 锁 防 盗 锁 K e n s i s i s i s i n g n g n g n g t t t t o n o n o n o n K e n K e n K e n...