Page 2
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. Nopart of this document may be reproduced,translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission.
Usage Notice Warning - To prevent the risk of fi re or shock hazards, do not expose this product to rain or moisture. Warning - Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit.
Package Overview LCD Display VGA Signal Cable Power Cord DC Power Supply RS-232 Cable USB Cable ( A to B ) (LA1950RTR/RTC/RTS only) (LA1950RTR/RTC/RTS only) Quick Start Guide Bracket Screw...
Note: You will need a screwdriver to attach the L-brackets. Your kiosk touch monitor included two L-brackets (and four screws, M4x6). This equipment is intended to be mounted in accordance with the proper hardware and the installation instructions supplied with the product. Use of mounting brackets or screws other than those specifi...
To setup this display, please refer to the following fi gure and procedures. 1. Be sure all equipment is turned off. 2. Connect the DC adapter to the power connector on the monitor and the other end into an electrical outlet (10.1).
User Controls Back Panel Controls Menu off status Menu appear Brightness Contrast Enter/Select sub-item function Power On/Off Power Enter Down Menu on status Menu disappear/return to main item Main item select up/Adjust up Main item select down/Adjust down Menu...
6. To Lock the OSD / Power menu buttons, please follow the instructions below. (Please note: the monitor has to be turned ON with a valid signal preset) (a.) Press “Menu” key , the OSD menu will pops upon display.
On-Screen Display Menus Main OSD Menu: ITEM CONTENT The monitor luminance level control. Contrast The monitor backlight level control. Brightness Fine-tune the image to full screen automatically. Auto Adjust Moving screen image horizontal position to left or right. Left/Right Moving screen image vertical position to up or down.
Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen. ► Check that all the I/O and power connectors are correctly and well connected described in the "Installation"...
The LCD display is under the power saving mode. In addition, the LCD display will enter power saving mode when experiencing a sudden signal disconnecting problem. The monitor can be activated by pressing any keyboard, triggering the mouse or touching the screen.
Compatibility Modes Mode Resolution IBM VGA 720X400 IBM VGA 640X480 Apple MacII 640X480 VESA VGA 640X480 VESA VGA 640X480 VESA VGA 800X600 VESA VGA 800X600 VESA VGA 800X600 VESA VGA 800X600 Apple Mac 832X624 VESA XGA 1024X768 VESA XGA 1024X768 VESA XGA 1024X768 VESA SXGA...
Touch Screen Driver Installation The LA1950RTR / LA1950RTC / LA1950RTS is available with both RS232 and USB connections. The touch driver is available online for these operating systems: Windows XP, 2000, ME, 98, NT4.0, CE, XP Embedded, Linux, Apple® Mac OS. Please Note: The LA1950RTR / LA1950RTC / LA1950RTS is Microsoft (Human Interface Device) compatible if you use the USB touch screen interface.
LA1950RTR / LA1950RTC / LA1950RTS Install Instructions: If you are using a PC running Windows follow the instructions below: 1. Power on the PC. 2. Be sure the USB or the RS-232 Serial cable is connected from the PC to the LCD display. 3.
Page 23
4. Connect the computer to the Touch Interface (RS-232 or USB) that you would like to use. 5. Download the Touch Driver online, then follow the step-by-step instructions as show on monitor. PLEASE NOTE! Don’t plug in both the RS-232 and USB cables! Doing so may cause a driver confl...
Product Registration and Technical Support Register Your Planar Products Today Thank you for choosing Planar. To assure you receive all the benefi ts of your Planar product and services, register your Planar product today. Visit our website to register your product at http://www.planar.com/support/product_registration.html.