Troubleshooting Guide - Intex ECO15230-1 Manual

(261IO) Sand Filter Pump & Saltwater System with Electrocatalysis Oxidation (14" & 16") ENGLISH 7.5" X 10.3" PANTONE 295U 05/25/2018

TROUBLESHOOTING GUIDE

TROUBLE
FILTER MOTOR FAILS
TO START
FILTER DOESN'T
CLEAN POOL
FILTER DOESN'T PUMP
WATER OR FLOW IS
VERY SLOW
PUMP DOESN'T
WORK
6-WAY VALVE/COVER
LEAKING
HOSE LEAKING
PRESSURE GAUGE
DOESN'T WORK
SAND IS FLOWING
BACK INTO THE POOL
INLET THREADED
AIR CONNECTOR / AIR
JET VALVE LEAKING
SAVE THESE INSTRUCTIONS
CAUSE
• The power cord is loose.
• The RCD circuit breaker is
tripped.
• Motor too hot and overload
protection is shut off.
• Stand-by/power saving mode.
• Without cyanuric acid.
• Improper chlorine or pH levels.
• No filtering media in tank.
• Wrong 6-way valve setting position.
• Excessively dirty pool.
• Dirt or sand on pool floor.
• The basket is restricting the water
flow.
• Clogged inlet or discharge.
• An air leak on the intake line.
• Excessively dirty pool.
• Sand media clogged with dirt.
• Nozzle and strainer connections
are reversed.
• Crusting or caking on the filtering
sand surface.
• Pool vacuuming device attached
to the system.
• Inlet threaded air connector
connected to the wrong hole on
the liner.
• Low water level.
• Strainer screen clogged up.
• An air leak on the intake hose.
• Faulty motor or the impeller is jammed.
• Sand tank o-ring missing.
• Sand tank o-ring dirty.
• Flange clamp not tight.
• 6-way valve damage.
• Hose nut not securely tight.
• Hose connection fitting o-ring/
L-shape o-ring missing.
• Clogged inlet of the pressure
gauge.
• Pressure gauge damage.
• Sand is too small.
• Sand bed is calcified.
• Plunger valve not well-fitted.
• Air jet valve is not tight and facing
up.
• Air jet valve internal seal locked.
• Air jet valve internal seal dirty.
• Air jet valve broken.
SOLUTION
• Line cord must be plugged into a 3 wire outlet that is
protected by a Class A Ground Fault Circuit Interrupter,
or RCD.
• Reset circuit breaker. If circuit breaker trips repeatedly,
your electrical system may have a defect. Turn off circuit
breaker and call an electrician to correct the problem.
• Let the motor cool down and restart again.
• See "Saltwater system operation".
• See "Cyanuric acid table".
• Adjust the chlorine and pH level. Consult your local
swimming pool supply stores.
• Load with filter sand, see "sand loading instructions".
• Set valve to "FILTER" position.
• Operate the filter for longer periods.
• Use Intex pool vacuum to clean bottom of pool.
• Clean the basket.
• Clear any obstructions in the intake hose by
discharging it inside pool wall.
• Tighten hose nuts, check hoses for damage, check
pool water level.
• Clean the pre-filtering basket more often.
• Backwash filter.
• Install the nozzle at the upper position of the pool inlet,
and the strainer at the lower position of the pool outlet.
• Remove about 1" of sand if necessary.
• Remove any pool vacuuming device attached to the
system line.
• Make sure the inlet threaded air connector is
connected to the pool inlet upper hole.
• Fill pool to correct water level.
• Clean strainer screens at pool inlet.
• Tighten hose nuts, check hose for damage.
• Contact Intex service center.
• Remove 6-way valve cover and ensure the
o-ring is in place.
• Clean sand tank o-ring with garden hose water.
• Tighten securely.
• Contact Intex service center.
• Tighten/reinstall hose nut.
• Ensure o-ring/L-shape o-ring is in place and
not damaged.
• Clear any obstructions in the intake by
unscrewing it from the 6-way valve.
• Contact Intex service center.
• Use only No. 20 silica sand with particle size
range 0.45 to 0.85 mm (0.018 to 0.033 inches)
and a Uniformity Coefficient less than 1.75.
• Change sand.
• Tighten or reinstall plunger valve.
• Tighten air jet valve and make sure it's facing up.
• Turn pump ON and run for few seconds, then
turn OFF, repeat 3 times.
• Remove air jet valve, flush dirt out with water and
replace valve back.
• Replace a new air jet valve.
English
261A
Page 30