Connecting The Units; Connecting The Power Cord; When Connecting To Separately Sold Power Amp - Pioneer AVH-P6000DVD Installation Manual

Connecting the Units

Connecting the Units

Connecting the power cord

IP-BUS input (Blue)
16 cm (6-1/4 in.)
Violet/white
Refer to Fig. 4.
IP-BUS cable
This product
Multi-CD player
(sold separately)
Yellow/black
If you use equipment with Mute function, wire this lead to
the Audio Mute lead on that piece of equipment. If not,
keep the Audio Mute lead free of any connections.
Red
Fuse resistor
To electric terminal controlled
by ignition switch (12 V DC)
ON/OFF.
LIGHT GREEN LEAD AT POWER CONNECTOR IS DESIGNED TO
Orange/white DETECT PARKED STATUS AND MUST BE CONNECTED TO THE
Fuse resistor
To lighting switch terminal. POWER SUPPLY SIDE OF THE PARKING BRAKE SWITCH. IMPROPER
CONNECTION OR USE OF THIS LEAD MAY VIOLATE APPLICABLE
LAW AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.
Yellow
Fuse (10 A)
Light green
To terminal always supplied
Used to detect the ON/OFF status of the parking brake.
with power regardless of
This lead must be connected to the power supply side of the parking
ignition switch position.
brake switch.
Black (ground)
To vehicle (metal) body.
Gray
White
+ +
Front speaker Front speaker
≠ ≠
Gray/black
White/black
Left Right
Violet
Green
+ +
Rear speaker Rear speaker
≠ ≠
Green/black Violet/black
20 cm AUX input jack
(7-7/8 in.)
Antenna cable
15 cm
(5-7/8 in.)
Connection method
1. Clamp the lead.
Note:
• The position of the parking brake switch depends
on the vehicle model. For details, consult the
vehicle Owner's Manual or dealer.
WARNING
Power supply side
Ground side
Blue/white
To system control terminal of the power amp
or Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
With a 2 speaker system, do not connect anything
to the speaker leads that are not connected to speakers.
When you connect the separately sold multi-channel processor
(DEQ-P8000) to this unit, do not connect anything to the
speaker leads and system remote control (blue/white).

When connecting to separately sold power amp

This product
2. Clamp firmly with
needle-nosed
pliers.
Parking brake
switch
Fig. 2
Subwoofer output
or non fading output
(SUBWOOFER OUTPUT or
NON-FADING OUTPUT)
23 cm (9 in.)
Front output
(FRONT OUTPUT)
15 cm (5-7/8 in.)
Rear output
(REAR OUTPUT)
15 cm (5-7/8 in.)
Blue/white
To system control terminal of the power amp or
Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
When you connect the separately sold
multi-channel processor (e.g. DEQ-P8000)
to this unit, do not connect anything to the
speaker leads and system remote control
Front speaker
(blue/white).
Note :
When you connect the multi-channel processor
to this unit, a separately sold power amp must
Rear speaker
be connected to the multi-channel processor.
Left
Note :
Subwoofer
Change the initial setting of this product
(refer to the Operation Manual).
The subwoofer output of this unit is monaural.
<ENGLISH> <ENGLISH>
Power amp
(sold separately)
Power amp
(sold separately)
Connecting cords
with RCA pin plugs
(sold separately)
Power amp
(sold separately)
System remote control
Blue/white
+ +
Front speaker
≠ ≠
+ +
Rear speaker
≠ ≠
Right
+ +
Subwoofer
≠ ≠
Perform these connections when using the
optional amplifier.
Fig. 3