Bionaire BW2100, BW2100R - Twin Window Fan Manual

INSTALLATION INSTRUCTIONS

Carefully unpack contents from carton.

1. Front Grill
2. Control Panel
3. Mode Button
4. LED Display
5. Temp Up (+)
6. Temp Down (-)

7. Fan Directional Switches (2)
8. Built-in Extender Screen
9. Extender Locks (2)
10. Extender Panels (2) (not shown)
11. Remote Control (For BW2100R only - not shown)

FOR DOUBLE-HUNG AND SLIDER WINDOWS

NOTE:
FOR SLIDER WINDOW, SET THE FAN VERTICALLY IN YOUR WINDOW OPENING WITH THE LEFT SIDE OF THE FAN SITUATED ON THE BOTTOM AND THE BUILT-IN EXTENDER SCREEN FACING UPWARDS.

1. Set the fan into your window opening (note that thewindow screen does not have to be removed or left open.)
2. If the fan does not fit snugly to the top and bottom ofthe window casing, attach the "Extender Panel(s)" and adjust the built in extender screen until the fan fits safely in your window. (See Figure 2)
   
3. To keep the fan in place, carefully close the windowso that the bottom edge of the window rests on the flat area at the flat top of the fan.

BE SURE FAN IS SECURELY INSTALLED IN YOUR WINDOW AT ALL TIMES. DO NOT LEAN OR PUSH ON FAN WHILE IT IS IN THE WINDOW.

OPERATING INSTRUCTIONS

1. Plug cord into any standard 120 volt AC outlet. Pleasemake sure the speed control is in the off position.
2. To turn the fan on and control the speed, press themode button. Note that pressing the mode button will allow you to cycle through the speed setting (High=3, Med=2, Low=1) as well as the Automatic Thermostat Temperature settings (Auto High = A3, Auto Medium = A2, Auto Low = A1). 0 indicates the Off position.
3. Set the airflow direction by sliding the fan directionalswitches located above each fan blade. Note that the fan blades work independently from one another and can be used for air intake (bring fresh air in from outside), exhaust (push air out from within the room) or exchange (cycles air in and out of the room simultaneously).

AUTO MODE

Your fan is equipped with a Programmable Digital Thermostat that will automatically turn the fan ON and OFF depending upon the preset comfort temperature. This is ideal for night time operation when temperatures can drop below comfort levels.

For example, if you set your fan to 75 degrees and the temperature drops to 74 degrees then the fan will automatically turn off. The fan will automatically turn on again when the room temperature exceeds the set temperature.

SETTING AUTO MODE

1. Press the Mode button to scroll to the desired autospeed setting (A3, A2, or A1).
2. Choose the desired temperature setting by pressingthe Temp Up (+) or Temp Down (-) buttons. You may select a temperature between 60 and 80 degrees Fahrenheit. Once the desired temperature is set, the digital display will return to show the ambient room temperature. View the set temperature by pressing either the Temp Up (+) or Temp Down (-) buttons.

If the fan does not start in the Auto mode, please be sure that the set temperature is below the current room temperature. Lower the set temperature if you would like the fan to start or switch over to the manual speed modes.

SETTING THE TIMER

1. Hold both the Temp Up (+) and Temp Down (-) buttons down until the digital display flashes "00".
2. Press the (+) or (-) buttons to change time in 1 hour increments. Note selection ranges from 1 to 16 hours. When in the timer mode, the time remaining will be displayed.

NOTE:
If Timer is set when fan is ON, the time displayed will turn the fan OFF once elapsed. If Timer is set when fan is OFF, the time displayed will turn the fan ON. (The default ON speed setting is Manual Low).

NOTE:
Timer function can be turned off by pressing the MODE key at any time.

REMOTE CONTROL (FOR BW2100R ONLY)

Your remote control requires (2) AAA batteries (included) for operation. To install the batteries, simply depress the back of the remote with your thumb on the indentations. Insert batteries according to the diagram shown inside and replace cover. The remote controls the Mode, Speed, Temperature, and Timer settings.

• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc),or rechargeable (nickel-cadmium) batteries.

CLEANING/MAINTENANCE INSTRUCTIONS

Follow these instructions to correctly and safely care for your fan. Please remember:

• Always unplug the fan before cleaning.
• Do not allow water to drip on or enter into fan housing.
• Be sure to use a soft cloth moistened with a mildsoap solution.
• Do not use gasoline, thinner or benzene as a cleaner.

FAN CLEANING

Clean the fan grills, extender screen, and extender panels with a soft, damp cloth. Please use caution around the motor housing area. Do not allow the motor or other electrical components to be exposed to water. Also, using a soft bristle brush attachment, a vacuum cleaner may be used to extract dust buildup on the grill areas. Note to turn the fan off before cleaning.

FAN STORAGE INSTRUCTIONS

When storing your fan in the off season, it is important to keep it in a safe dry location. It is important to protect the fan head from dust. We strongly recommend using the original box from purchase.

• We recommend using the original (or appropriately sized) box.
• Please remember to protect the fan from dust or moisture.

WINDOW FAN ACCESSORIES

Window Fan Extender Panel

To order please go to www.bionaire.com or call 1-800-253-2764

If you have any questions regarding your product or would like to learn more about other Bionaire^® products, please contact our Consumer Service Department at 1-800-253-2764 or visit our website at www.bionaire.com

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Bionaire BW2100, BW2100R - Twin Window Fan Manual