Toshiba RAS-24J2AVSG-E Owner's Manual page 4

INDOOR UNIT DISPLAY
1
● Display brightness can be adjusted, follow procedure on (.
Require Wireless LAN connecting adapter which available as accessory.
PREPARATION BEFORE USE
2
Preparing Filters
1. Open the air inlet grille and remove the air filters.
2. Attach the filters. (see detail in the accessory sheet).
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
1. Push by tip of the pencil.
If timer indication is flashing, go to the next step 2.
2. Press or
3. Press : Set the time.
Remote Control Reset
Push by tip of the pencil or
1. Remove the batteries.
2. Press .
3. Insert the batteries.
AIR FLOW DIRECTION
3
1
Press : Move the louver
in the desired vertical direction.
FIX
Press : Move the
2
louver in the desired horizontal
direction.
Press : For select
louver swing operation.
Pi
Vertical Horizontal
(Up-Down) (Left-Right)
Swing Swing
3
Pi Pi Pi
Up-Down
Swing off Left-Right
Swing
Note:
● Do not move the louver manually by hands or others.
● The louver may automation positioning by some operation mode.
1 ECO (White)
2 Wi-Fi access (White)
3 Hi-Power (White)
4 Timer (White)
5 Operation Mode
- Cool (Blue)
- Heat (Orange)
: adjust the time.
● Vertical (Up-Down) swing
Pi
● Horizontal (Left-Right) swing
REMOTE CONTROL
4
1 Infrared signal emitter
2 Memory and Preset button (PRESET)
3 Start/Stop button
4 Mode select button (MODE)
5 Air fl ow button
6 Fireplace/8°C button
7 ECO button
8 Comfort sleep button (COMFORT SLEEP)
9 Weekly timer (ON/OFF)
! Temp for Weekly timer
" On timer button (ON)
# Set clock button (CLOCK)
$ Check button (CHECK)
% Filter reset button (FILTER)
& Temperature button (TEMP)
( Swing louver button (SWING)
) Fan speed button (FAN)
~ Set louver Left-Right button (FIX W)
+ Set louver Up-Down button (FIX X)
, High power button (Hi-POWER)
- Power selection/Silent button (P-SEL/SILENT)
. Program P1 - P4
/ Day/Edit button
: Setup button (SET)
; Off timer button (OFF)
< Clear button (CLR)
= Reset button (RESET)
Note:
● The provided Remote Controller is a wireless type, which also can be
used as a wire. Please see "How to Connect The Remote Controller
for Wired Operation", located in installation instruction, in case of wired
control is required.
● In wire operation, remote controller will return to initial condition
(PRESET, TIMER and CLOCK will return to initial condition) when user
shutdown power supply of Air conditioner.
COOLING / HEATING / FAN ONLY
5
OPERATION
1. Press : Select Cool
2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.
Fan Only: No temperature indication
3. Press : Select AUTO, LOW , LOW+
MED+ , HIGH
AUTOMATIC OPERATION
6
To automatically select cooling, heating, or fan only operation
1. Press : Select Auto A.
2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.
3. Press : Select AUTO, LOW , LOW+
MED+ , HIGH
DRY OPERATION
7
For dehumidification, a moderate cooling performance is controlled
automatically.
1. Press : Select Dry
2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.
Note: DRY mode fan speed is set to Auto only.
Hi-POWER OPERATION
8
To automatically control room temperature and airflow for faster cooling or
heating operation (except in DRY and FAN ONLY mode)
Press : Start and stop the operation.
1
2
3
4
5
6
7
8
9
!
"
#
$
%
, Heat , or Fan only .
, MED
or Quiet
, MED
or Quiet
.
&
(
)
~
+
,
-
.
/
:
;
<
=
,
,