Page 1
MWM-1100 Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model MWM-1100 Retain This Manual for Reference 08-10-09 ® IMPEX INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 OWNER'S Tel: (800) 999-8899 Fax: (626) 961-9966 MANUAL www.impex-fitness.com info@impex-fitness.com...
ORDERING PARTS..................…………. 22 BEFORE YOU BEGIN Thank you for selecting the MARCY MWM-1100 HOME GYM by Impex Inc. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES RESPONSIBILITY PERSONAL INJURY PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
Page 4
WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-999-8899 for replacements. Apply the labels in the location shown.
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Slide two Ø 2 ½” x 1” Rubber Bumpers (#35) onto the two Guide Rods (#5). Insert the two Guide Rods into the holes on the Rear Stabilizer (#2).
Page 9
STEP 2 (See Diagram 2) A.) Slide 9 Weight Plates (#50) onto the Guide Rods (#5). Make sure the deep groove on the Weight Plate are facing down and toward the back of the Machine. B.) Align the holes on the Weight Plates. Insert a Selector Rod (#16) through the center hole. Use the L-shaped Pin (#57) to select the number of Weight Plates for exercise.
Page 11
STEP 3 (See Diagram 3) A.) Attach the Seat Support (#9) to the Vertical Frame (#3). Secure it with two M10 x 2 ½” Carriage Bolts (#60), one 5 1/8” x 1 5/8” Bracket (#21), two Ø ¾” Washers (#70), and two M10 Aircraft Nuts (#72).
Page 12
STEP 4 (See Diagram 4) A.) Attach two Ø 1” x Ø ½” Bushings (#53) to the holes on Upper Frame (#4). Attach the Front Press Base (#6) to the two Bushings. Secure it with one M12 x 3 3/8” Hex Bolt (#61), two Ø 1”...
Page 15
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 136” Upper Cable (#26) to the front opening on the Upper Frame (#4). NOTE: The Ball Stopper on the Cable needs to be underneath the Frame. B.) Attach a Pulley (#38) to the forward most opening. Secure it with one M10 x 2 3/8” Allen Bolt (#64), two Ø...
Page 17
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 108” Butterfly Cable (#27) to the hook on the Right Butterfly (#8). Draw the Cable towards the right open Swivel Pulley Bracket (#17). B.) Attach a Pulley (#38) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#63), two ∅ ¾” Washers (#70), and one M10 Aircraft Nut (#72).
Page 18
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 142” Lower Cable (#28) to the opening on the bottom of the Leg Developer (#10). B.) Attach a Pulley (#38) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#64), two ∅...
PARTS LIST KEY NO. DESCRIPTION Q’ty Main Base Frame Ankle Strap Rear Stabilizer Single Handle Vertical Frame Ø 1” x Ø ½” Bushing Upper Frame Ø ¾” Leg Developer Bushing Guide Rod Plastic Ring Front Press Base Rivet Left Butterfly L-shaped Pin Right Butterfly M6 x 1 3/8”...
IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.