Table of Contents
Advertisement
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Resistance Chart
Model
MWM CR5N
Retain This
Manual for
Reference
07-24-03
OWNER'S
MANUAL
MARCY CORNER GYM
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
CR 5N
Advertisement
Table of Contents
Related Manuals for Impex CR-5
Summary of Contents for Impex CR-5
- Page 1 Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model MWM CR5N Retain This Manual for Reference 07-24-03 OWNER'S IMPEX FITNESS PRODUCTS MANUAL 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.com...
-
Page 2: Table Of Contents
ORDERING PARTS..................25 BEFORE YOU BEGIN Thank you for selecting the MARCY CR5N CORNER GYM by IMPEX FITNESS PRODUCTS. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. -
Page 3: Important Safety Notices
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. -
Page 5: Assembly Instructions
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Right Base Frame (#46) and Left Base Frame (#87) on the floor, at a right angle to each other. - Page 6 STEP 2 (See Diagram 2) A.) Attach the Right Vertical Beam (#21) to the Right Base Frame (#46). Secure it with two M10 x 2 ¾” Carriage Bolts (#17), ¾” Washers (#6), and M10 Aircraft Nuts (#5). B.) Attach the Right Seat Support (#49) to the Right Vertical Beam (#21). Secure it with one Bracket (#7), two M10 x 2 ¾”...
- Page 7 STEP 3 (See Diagram 3) A.) Slide two 2 ½” Rubber Bumpers (#58) onto two Chromed Guide Rods (#58). Insert the two Guide Rods into the holes on the Right Base Frame (#46). Slide the Selector Stem (#67) onto the two Guide Rods (#22). Slide the Selector Stem over the Selector Rod (#69). Secure the Selector Rod to the Selector Stem with two M10 x 1”...
- Page 8 DIAGRAM 3...
- Page 9 STEP 4 (See Diagram 4) A.) Attach the Front Press Base (#97) to the Right Base Frame (#46). Secure it with a 9 ¼” Front Press Axle (#60), two ¾” Washers (#6), and two M10 Aircraft Nuts (#5). B.) Attach the Front Press Frames (#63) to the Front Press Base. Secure it with four M10 x 2 ¾” Carriage Bolts (#17), ¾”...
- Page 10 STEP 5 (See Diagram 5) A.) Attach the Butterfly Support Frame (#18) to the front of Right Vertical Beam (#21). Attach the Butter Pulley Support (#74) to the back of Right Vertical Beam. Align the holes. Secure them together with two M10 x 2 ¾” Carriage Bolts (#17), ¾”...
- Page 11 STEP 6 (See Diagram 6) A.) Attach the Vertical Press Frame (#78) to the Rear Vertical Beam (#50). Secure it with a M10 x 4 7/8” Vertical Press Axle (#81), two ¾” Washers (#6), and two M10 x 1” Allen Bolts (#56). B.) Place the Vertical Press Frame rest onto the 1 ½”...
- Page 12 CABLE LOOP DIAGRAM...
- Page 13 STEP 7 (Upper Cable Loop & Diagram 7) A.) Attach the 108” Upper Cable (#93) to the front opening on the Upper Frame (#8). Attach a Pulley (#79) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two Pulley Bushings (#11), and one M10 Aircraft Nut (#5).
- Page 14 DIAGRAM 7...
- Page 15 STEP 8 (See Butterfly Cable Loop & Diagram 8) A.) Attach the 106” Butterfly Cable (#95) to the slot on the back of Left Butterfly (#20). Draw the Cable through the slot then to the open left Swivel Pulley Bracket (#72). B.) Attach a Pulley (#79) to the bracket.
- Page 16 DIAGRAM 8...
- Page 17 STEP 9 (See Front Press Cable Loop & Diagram 9) A.) Attach the 224” Front Press Cable (#94) to the lower opening on the Leg Developer (#40). B.) Attach a Pulley (#79) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two Pulley Bushings (#11), and one M10 Aircraft Nut (#5).
- Page 18 DIAGRAM 9...
- Page 19 STEP 10 (See Leg Press Cable Loop & Diagram 10) A.) Attach one end of the 82” Leg Press Cable (#96) to the open slot on the back of the Leg Press Frame (#84). Secure it with one M10 x 2 ½” Allen Bolt (#10), two ¾”...
- Page 20 DIAGRAM 10...
- Page 21 STEP 11 (See Diagram 11) A.) Place a Seat Pad (#29) onto the Left Seat Support (#92). Secure it with two M8 x 2 1/8” Allen Bolts (#25) and 5/8” Washers (#24). B.) Attach a Backrest Board (#28) to the Left Vertical Beam (#77). Secure it with two M8 x 2 1/8” Allen Bolts (#25) and 5/8”...
- Page 22 STEP 12 (See Diagram 12) A.) Place a Seat Pad (#29) onto the Right Seat Support (#49). Secure it with two M8 x 2 1/8” Allen Bolts (#25) and 5/8” Washers (#24). B.) Attach a Backrest Board (#28) to the Right Vertical Beam (#21). Secure it with two M8 x 2 1/8” Allen Bolts (#25) and 5/8”...
- Page 23 STEP 13 (See Diagram 13) A.) Securely tighten all the nuts and bolts previously installed. B.) Before putting the Weight Plates on, now move the machine to the corner of the room or place where you will use the machine. C.) Lift up the Selector Rod and install one stack of 19 Weight Plates (#66).
-
Page 24: Parts List
PARTS LIST KEY NO. DESCRIPTION Q’ty M5 Screw Lat Bar Grip Magnet Box Lat Bar Magnet Chain Selector Pin C-clip M10 x 1” Allen Bolt M10 Aircraft Nut M12 Aircraft Nut ¾” Washer 2 ½” Rubber Bumper Bracket Flat Double Floating Pulley Bracket 1 Upper Frame 9 ¼”... -
Page 25: Resistance Chart
WEIGHT RESISTANCE CHART WEIGHT PLATE Station Low Pulley 105 115 Lat Pull Butterfly Leg Press Front Press 110 120 Vertical Press WEIGHT PLATE Station Low Pulley 125 135 145 155 165 175 185 195 205 215 Lat Pull 110 120 130 140 150 160 170 180 190 200 Butterfly 101 108 115 122 129 136 Leg Press... -
Page 26: Warranty
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option.