Table of Contents
Advertisement
Section 1: Assembly & Set-up
Section 1: Assembly & Set-up
Tractor Requirements
Horsepower
Tractor horsepower should be within the range noted
below. Tractors outside the range must not be used.
Horsepower rating . . . . . . . . . . . . . . . . . . . 50-160 hp
Hitch type (See Drawbar Set-up) . . . . . . . . . Drawbar
Rear power take-off speed:
RC3615 . . . . . . . . . . . . . . . . . . . . . . . . . . . 540 rpm
RCM3615 . . . . . . . . . . . . . . . . . . . . . . . . .1000 rpm
Hydraulic outlets (See Hydraulic Set-up)
Factory standard . . . . . . . . . . . . . . 2 Duplex outlets
Independent wing raising . . . . . . . 3 Duplex outlets
Drawbar Set-up
Refer to Figure 1-1:
!
DANGER
To avoid serious injury or death:
Do not use a power take-off adapter. The adapter will increase
strain on the tractor's power take-off shaft causing possible
damage to shaft and driveline. It will also defeat the purpose
of the tractor's power take-off shield.
!
WARNING
To avoid serious injury or death:
•
Do not use a tractor that is too small or too large. Small
tractors can be pushed around and flipped over. Large
tractors can damage the attached implement.
•
Power take-off damage may occur if distances "A" and
"B" are not properly maintained.
Maintain proper distance, dimension "A" , between center
of drawbar hitch pin hole and end of tractor power take-off
shaft.
540 rpm & 1 3/8" @ 1000 rpm power take-off speed:
"A" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14"- 16"
"B" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8" - 10"
"C" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18" to 22"
22273
A
Power Take-Off Shaft
Drawbar
Ground Level
Power Take-Off to Drawbar Distance
Figure 1-1
12
RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M
Table of Contents
Hydraulic Outlets
The number of tractor hydraulic duplex outlets is
dependent upon how the Rotary Cutter is set-up.
•
Two duplex outlets are required if the wings are folded
up and down simultaneously. (Factory standard)
•
Three duplex outlets are required if the wings are
folded up and down independently.
If the tractor does not have the necessary number of
duplex outlets, there are control valve kits available to
add outlets. See "Hydraulic Accessories" on page 39
for a complete description of this kit.
Before You Start
Read and understand the operator's manual for your
cutter. An understanding of how it works will aid in the
assembly and setup of your cutter.
It is best to go through the Assembly Checklist before
assembling the cutter. Speed up your assembly task and
make the job safer by having all needed parts and
equipment readily at hand.
Torque Requirements
See "Torque Values Chart for Common Bolt Sizes" on
page 58 to determine correct torque values when
tightening hardware. See "Additional Torque Values" at
bottom of chart for exceptions to common torque values.
Have a fork lift or loader with properly sized chains and safety
stands capable of lifting and supporting the equipment on hand.
Have a minimum of two people available during assembly.
Make sure all major components and loose parts
are shipped with the machine.
Double check to make sure all parts, fasteners,
and pins are installed in the correct location. Refer
to the Parts Manual if unsure. By double checking,
you will lessen the chance of using a bolt
incorrectly that may be needed later.
NOTE: All assembled hardware from the factory
has been installed in the correct location.
Remember location of a part or fastener if removed
during assembly. Keep parts separated.
Make sure working parts move freely, bolts are
tight & cotter pins are spread.
B
Make sure all grease fittings are in place and
lubricated.
Make sure all safety labels are correctly located
and legible. Replace if damaged.
C
Make sure all red and amber reflectors are
correctly located and visible when machine is in
transport position.
Make sure all pneumatic tires are properly inflated
and all wheel bolts and axle nuts are tightened to
the specified torque.
Assembly Checklist
Check
Ref.
Operator's
Manual
Operator's
Manual
330-502M
Parts
Manual
331-939P
Page 58
Page 48
Page 4
Page 10
Page 58
12/12/18
Advertisement
Table of Contents
