Section 1: Assembly & Set-Up; Before You Start; Torque Requirements - Land Pride RC3615 Operator's Manual

Section 1: Assembly & Set-up
Section 1: Assembly & Set-up
Tractor Requirements
Horsepower
Tractor horsepower should be within the range noted
below. Tractors outside the horsepower range must not
be used. If the tractor is too small, it can be pushed
around and/or flipped over by the weight of the cutter. Too
large a tractor can damage the cutter.
Horsepower Rating . . . . . . . . . . . . . . . . . . 50-160 HP
Drawbar Set-up
Refer to Figure 1-1:
Maintain proper distance, dimension "A" , between center
of drawbar hitch pin hole and end of tractor PTO shaft.
Hitch Type. . . . . . . . . . . . . . . . . . . . . . . . . . Draw Bar
540 RPM & 1 3/8" @ 1000 RPM Rear PTO Speed:
"A". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14"- 16"
"B" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8" - 10"
"C" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18" to 22"
1 3/4" @ 1000 RPM Rear PTO Speed:
"A". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18" - 20"
"B" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10" - 12"
"C" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18" to 22"
IMPORTANT: PTO damage may occur if distances
"A" and "B" are not properly maintained.
IMPORTANT: A PTO adaptor should not be used.
Using a PTO adaptor can damage the PTO.
PTO to Drawbar Distance
Figure 1-1
PTO Speed
Rear PTO Speed:
Model RC3615. . . . . . . . . . . . . . . . . . . . . 540 RPM
Model RCM3615 . . . . . . . . . . . . . . . . . . .1000 RPM
Hydraulic Outlets
The number of tractor hydraulic duplex outlets is
dependent upon how the Rotary Cutter is set-up.
•
Two duplex outlets are required if the wings are raised
and lowered simultaneously. (Factory standard)
4/20/15
Table of Contents
•
Three duplex outlets are required if the wings are
raised and lowered independently. (Requires
Hydraulic Wing Control Kit on page 30 to raise wings
independently.)
•
If the tractor does not have the necessary number of
duplex outlets, control valve kits are available to add
outlets. See "Hydraulic Accessories" on page 30 for
a complete description of the kits.

Before You Start

Read and understand the Operator's Manual for your
cutter. An understanding of how it works will aid in the
assembly and setup of your cutter.
It is best to go through the Pre-Assembly Checklist
before assembling the cutter. Speed up your assembly
task and make the job safer by having all needed parts
and equipment readily at hand.

Torque Requirements

See "Torque Values Chart for Common Bolt Sizes" on
page 50 to determine correct torque values when
tightening hardware. See "Additional Torque Values" at
bottom of chart for exceptions to common torque values.
Have a fork lift or loader with properly sized chains and safety
stands capable of lifting and supporting the equipment on hand.
Have a minimum of two people available during assembly.
Make sure all major components and loose
parts are shipped with the machine.
Double check to make sure all parts, fasteners,
and pins are installed in the correct location.
Refer to the Parts Manual if unsure. By double
checking, you will lessen the chance of using a
bolt incorrectly that may be needed later.
NOTE: All assembled hardware from the
factory has been installed in the correct
location. Remember location of a part or
fastener if removed during assembly. Keep
parts separated.
22273 Make sure working parts move freely, bolts are
tight & cotter pins are spread.
Make sure all grease fittings are in place and
lubricated.
Make sure all safety labels are correctly
located and legible. Replace if damaged.
Make sure all red and amber reflectors are
correctly located and visible when machine is
in transport position.
Make sure all tires are inflated to the specified
psi air pressure and all wheel bolts and axle
nuts are tightened to the specified torque.
RC3615 (540 RPM) and RCM3615 (1000 RPM) Rotary Cutters 330-502M
Pre-Assembly Checklist
Check Reference
Operator's
Manual
Operator's
Manual
330-502M
Parts Manual
330-502P
Page 50
Page 40
Page 4
Page 9
Page 50
11