Related Manuals for LG 26LC51(C)
Summary of Contents for LG 26LC51(C)
- Page 1 website:http://biz.LGservice.com LCD TV SERVICE MANUAL CHASSIS : LP78A MODEL : 26LC51(C) 26LC51(C)-ZA MODEL : 26LC7R 26LC7R-ZA CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
-
Page 2: Table Of Contents
CONTENTS CONTENTS ....................2 SAFETY PRECAUTIONS ................3 SPECIFICATION ..................6 ADJUSTMENT INSTRUCTION ..............9 TROUBLE SHOOTING ................17 BLOCK DIAGRAM...................25 EXPLODED VIEW .................. 26 EXPLODED VIEW PARTS LIST ..............27 REPLACEMENT PARTS LIST ............... 28 SVC. SHEET ....................- 2 -... -
Page 3: Safety Precautions
SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. - Page 4 SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
- Page 5 IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
-
Page 6: Specification
SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement. 1. Application range (4) Specification and performance of each parts are followed each drawing and specification by part number in This specification is applied to LP78A chassis. accordance with BOM. - Page 7 5. Model Specification(EU) Item Specification Remark Market Broadcasting system PAL BG/DK, PAL I/II, SECAM L/L’ Available Channel BAND VHF/UHF C1_C69 CATV S1_S47 Receiving system Upper Heterodyne SCART Input(2EA) PAL, SECAM, NTSC Full Scart 1EA, Harf 1EA Video Input (1EA) PAL, SECAM, NTSC Side AV S-Video Input (1EA) PAL, SECAM, NTSC...
- Page 8 8. HDMI input (DTV) Resolution H-freq(kHz) V-freq(kHz) Pixel clock(MHz) Proposed 720*480 15.75 60.00 13.514 SDTV, DVD 480I(525I) 720*480 15.73 59.94 13.500 SDTV, DVD 480I(525I) 720*576 15.625 50.00 13.500 SDTV, DVD 576I(625I) 50Hz 720*480 31.47 59.94 27.000 SDTV 480P 720*480 31.50 60.00 27.027 SDTV 480P...
-
Page 9: Adjustment Instruction
*Use for Windows 95/98 : Setup_LptDrv_v0104_9x.exe This spec sheet is applied all of the 26/32/37/42” LCD *Use for Windows 2000/XP : Setup_LptDrv_v0202_XP_2000.exe TV(LP78A) by manufacturing LG TV Plant all over the world. *Use for Windows NT : Setup_LptDrv_v0104_NT.exe 2. Specification (3) Verification (Start >... - Page 10 3) Double click the blue box and confirm "Bootloader Version" as 42. 4) Click the "Erase Flash" button => Select the "Bootloader.bat" file(install > VCTP_download > Bootloader) => Push "OK" 5) Double click the download file low, then "edit" window will be opened =>...
- Page 11 8) Click OK button at the "edit window". 4) Execute ‘Download.vi2c’ program in PC, then a main 9) Under Downloading process widow will be opened. 10) If download is failed, for example "No acknowledge from slave". Execute download again from(1). (2) Download method 2 (AV Plate Ass’y) 5) Double click the blue box and confirm "Bootloader Version"...
- Page 12 9) Choose the Hex file in folder and execute downloading 2) Connect Zig to TV using a D-sub cable. with click "open button". 3) Execute ‘Download_CS.vi2c’ program in PC, then a 10) Click OK button at the "edit window" main widow will be opened. 4) Click "GO"...
- Page 13 7) Double click the download file low then, "edit" window 12) If download is failed, for example "No acknowledge will be opened. from slave", execute download again from (1). 8) Chick the choice button I n the "edit window", then "file 4.3.
- Page 14 (5) Push the Update NVM from File 5. EDID (The Extended Display Identification Data ) /DDC download (Display Data Channel) * Caution - Use the proper signal cable for EDID Download. - Never connect HDMI & D-SUB Cable at the same time. - Use the proper cables below for EDID Writing.
- Page 15 => Detail EDID Options are below(a, b, c, d, e) a. Product ID b. Serial No : Controlled on production line c. Month, Year : Controlled on production line <EDID DATA> ex) Montly: '03' => '03' Year: '2005' => '0F' d.
- Page 16 (3) DDC adjustment support command set 6.4 Input the Shipping Option Data Adjustment CMD(HEX) 1) Push the ADJ key in a Adjust Remote control. Aging On/Off FF : ON / OO : OFF 2) Input the Option Number that was specified in the BOM, into the Shipping area.
-
Page 17: Troubleshooting
TROUBLESHOOTING 1. No power (1) Symptom 1) Minute discharge does not occur at module. 2) Front LED does not activate. (2) Press check Start Check Is the power cord Plug in the power cord. plugged in? Are the line filter and Connect the cable.(SC100) PSU connected? Is the... - Page 18 2. Protect mode (1) Symptom 1) After lighting once it does not discharge minutely from the module. 2) The relay falls.(there is an audible “Click”.) 3) The color of the front LED turns from green to red. (2) Follow check Start Check Is the output the normal Low/High Is the Power Board...
- Page 19 3. No Raster (1) Symptom 1) No OSD or image are displayed on the screen. 2) The front LED remains green. (2) Follow check Start Check Does Is output the normal Replace the Is the inverter minute discharge Low/High voltage except Power board.
- Page 20 5. In the case of an unusual display in rear AV mode. Is video input of the A/V jack normal? Check the input source. (Check R172) Sam as Block A 6. In the case of an unusual display in Side AV mode. Is the video input of Check the input source.
- Page 21 8. In the case of an unusual display in SCART 1 mode. Is the video input Check the input source. of the A/V jack normal? (Check R172) Sam as Block A 9. In the case of an unusual display in SCART 1_RGB mode. Is the video input of the A/V jack normal?(Check...
- Page 22 11. In the case of an unusual display in component 1 mode. Is the video input of the A/V jack Check the input source. normal? (Check R248, R249,R250) Change the IC(IC500) 12. In the case of an unusual display in component 2 mode. Is the video input of the A/V Jk202 Check the input source.
- Page 23 14. No Sound (1) Symptom 1) LED is green. 2) There is a picture but no sound. (2) Follow check Is there Set speaker on sound in any Is the speaker on? in the menu. mode? Is there Is the speaker Check the Speaker no sound only for Download the EDID data.
- Page 24 15. HDMI mode Is only video Download EDID data each port. normal? 1. Check TV input mode. (HDMI 1 port support HDMI and DVI. So if you input DVI signal and PC audio from phone jack, You can hear PC audio.) Is only audio 2.
-
Page 25: Block Diagram
BLOCK DIAGRAM - 25 -... -
Page 26: Exploded View
EXPLODED VIEW - 26 -... -
Page 27: Exploded View Parts List
EXPLODED VIEW PARTS LIST PART NO. DESCRIPTION EAB30826701 Speaker,Full Range EN1527C-6603-1. ND 7W 8OHM 80DB 170HZ 71.5 X 42 X 29.5 EAJ36325401 LCD,Module-TFT V260B1 L03 WXGA 16/9 800:1 - CHI MEI OPTOELECTRONICS CORP MGJ32424603 Plate PRESS EGI T1.0 METAL HGI MGJ32424607 Plate PRESS H-GI T1.0 METAL HGI 26LC7D top bar ”A”... -
Page 28: Replacement Parts List
REPLACEMENT PARTS LIST For Capacitor & Resistors, the CC, CX, CK, CN, CH : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit in the CQ : Polyestor RS : Metal Oxide Film P/No. means as follows; CE : Electrolytic RN : Metal Film CF : Fixed Film RH : CHIP, Metal Glazed(Chip) - Page 29 DATE: 2006. 12. 06. DATE: 2006. 12. 06. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION C547 0CK104CK56A 0603B104K500CT 100nF 10% 50V C640 0CE477BJ618 ESM477M035T1G5H20G 470uF 20% C548 0CK104CK56A 0603B104K500CT 100nF 10% 50V C641 0CE477BJ618 ESM477M035T1G5H20G 470uF 20%...
- Page 30 DATE: 2006. 12. 06. DATE: 2006. 12. 06. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION DIODEs AL310 6210TCE002B HB-4M3216-121JT 120OHM 3.2X1 D101 EAH33945901 CDS3C30GTH 30V 50V 120V 1.9A AL311 6210TCE002B HB-4M3216-121JT 120OHM 3.2X1 D102...
- Page 31 DATE: 2006. 12. 06. DATE: 2006. 12. 06. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION L810 EAP32842805 NR8040T150M 15UH 20% 0V 2.4A R119 0RJ1001D677 MCR03EZPJ102 1KOHM 5% 1/10W X300 6202TST001H SX-1 27MHZ 30PPM 27MHZ 30PPM R120...
- Page 32 DATE: 2006. 12. 06. DATE: 2006. 12. 06. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION R252 0RJ0332D677 MCR03EZPJ330 33OHM 5% 1/10W R352 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1 R253 0RJ0332D677 MCR03EZPJ330 33OHM 5% 1/10W R353...
- Page 33 DATE: 2006. 12. 06. DATE: 2006. 12. 06. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION R543 0RJ1001D677 MCR03EZPJ102 1KOHM 5% 1/10W R720 0RJ1002D677 MCR03EZPJ103 10KOHM 5% 1/10W R544 0RJ1001D677 MCR03EZPJ102 1KOHM 5% 1/10W R722 0RJ2002D677...
- Page 34 DATE: 2006. 12. 06. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION R100 0RH0332D622 MCR10EZHJ330 33OHM 5% 1/8W 2 R101 0RH0752D622 MCR10EZHJ750 75OHM 5% 1/8W 2 R102 0RH4700D622 MCR10EZHJ471 470OHM 5% 1/8W R103 0RH2203D622 MCR10EZHJ224 220KOHM 5% 1/8W R104 0RH4700D622 MCR10EZHJ471 470OHM 5% 1/8W R105...
- Page 38 Mar., 2007 P/NO : MFL36696901 Printed in Korea...