Advertisement
SAVE THESE INSTRUCTIONS FOR LATER USE.
FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE AUDIO EQUIPMENT.
Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power line surges.
Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
When the power supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.
If the product has been dropped or damaged in any way.
when the product exhibits a distinct change in performance-this indicates a need for service.
This reminder is provided to call the CATV system installer's attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
THE APPARATUS SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING, AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THE APPARATUS. AS WITH ANY ELECTRONIC PRODUCTS, USE CARE NOT TO SPILL LIQUIDS INTO ANY PART OF THE SYSTEM. LIQUIDS CAN CAUSE A FAILURE AND/OR A FIRE HAZARD.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions:
IC STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED "DANGEROUS VOLTAGE" WITHIN THE PRODUCT'S ENCLOSURE THAT MAYBE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
Changes or modifications to this equipment not expressly approved by NAD Electronics for compliance could void the user's authority to operate this equipment.
CAUTION REGARDING PLACEMENT
To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) that is equal to or greater than shown below.
NOTES ON ENVIRONMENTAL PROTECTION
At the end of its useful life, this product must not be disposed of with regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user's manual and packaging, point this out.
The materials can be reused in accordance with their markings. Through re-use, recycling of raw materials or other forms of recycling of old products, you are making an important contribution to the protection of our environment. Your local administrative office can advise you of the responsible waste disposal point.
INFORMATION ABOUT COLLECTION AND DISPOSAL OF WASTE BATTERIES (DIRECTIVE 2006/66/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF EUROPEAN UNION) (FOR EUROPEAN CUSTOMERS ONLY)
Batteries bearing any of these symbols indicate that they should be treated as "separate collection" and not as municipal waste. It is encouraged that necessary measures are implemented to maximize the separate collection of waste batteries and to minimize the disposal of batteries as mixed municipal waste.
End-users are exhorted not to dispose waste batteries as unsorted municipal waste. In order to achieve a high level of recycling waste batteries, discard waste batteries separately and properly through an accessible collection point in your vicinity. For more information about collection and recycling of waste batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.
By ensuring compliance and conformance to proper disposal of waste batteries, potential hazardous effects on human health is prevented and the negative impact of batteries and waste batteries on the environment is minimized, thus contributing to the protection, preservation and quality improvement of the environment.
* NAD is a trademark of NAD Electronics International, a division of Lenbrook Industries Limited Copyright 2015, NAD Electronics International, a division of Lenbrook Industries Limited
WHAT'S IN THE BOX
Packed with your D 3020 you will find:
SAVE THE PACKAGING
Please save the box and all the packaging in which your D 3020 arrived. Should you move or otherwise need to transport your D 3020, this is by far the safest container in which to do so. We've seen too many otherwise perfect components damaged in transit for lack of a proper shipping carton, so please: Save that box!
This simple guide will help you get started with your D 3020.
Place the D 3020 on a firm, level surface. Do not place the unit on a soft surface like a carpet.
Make all the connections to your D 3020 with the unit unplugged from the mains power source. It is also advisable to power down or unplug all associated components while making or breaking any signal or AC power connections.
Press and hold "BASS EQ" at the rear panel until D3020 defaults to COAX source.
VOLUME
Adjust audio level by turning clockwise or counterclockwise.
Rotating the volume knob will automatically restore audio from mute mode.
DISPLAY
Illuminate the selected or active Source (OPT1, OPT2, COAX, USB, AUX 1, AUX 2, BT) and current audio level.
Display will not adjust to the orientation of the unit. Display is best viewed with the D3020 in vertical position as shown above.
PHONES
BASS EQ
AUX 1
Use a twin RCA-to-RCA lead to connect these sockets to the left and right analog output of a CD player, preamplifier, processor or other applicable devices.
SUBW
Connect the SUBW output to powered ("active") subwoofers or to power amplifier channels driving a passive system.
SPEAKERS
Connect the right speaker to the terminals marked "R +" and "R-" ensuring that the "R+" is connected to the "+" terminal on your loudspeaker and the "R-" is connected to the loudspeaker's "-" terminal. Connect the left speaker to the terminals marked "L +" and "L-" ensuring that the "L+" is connected to the "+" terminal on your loudspeaker and the "L-" is connected to the loudspeaker's "-" terminal.
+12V TRIGGER IN
Connect this +12V Trigger input to the remote device's corresponding +12V DC output jack using a mono cable with 3.5mm male plug. The controlling device must be equipped with a +12V trigger output to use this feature.
USB
MINIMUM PC SYSTEM REQUIREMENT
Microsoft Windows XP Service Pack 2 or higher, Microsoft Windows 7
FOR MAC USERS
Minimum Mac OS X Snow Leopard (version 10.6) and later versions
NOTE
Download and install to your PC the NAD USB Audio driver from the Manuals/Downloads tab of the NAD web address http://nadelectronics.com/products/digital-music/D-3020-Hybrid-Digital-Amplifier.
DIGITAL AUDIO INPUT (OPT1, OPT2, COAXIAL)
Connect to the corresponding optical or coaxial digital output of sources such as CD or BD/DVD players, digital cable box, digital tuners and other applicable components.
The digital audio input is 24/192 capable and can accept PCM audio signal only. Ensure that the digital audio output of your source is set to PCM before connecting to the digital audio input of D 3020.
Pair Bluetooth device with the unique device ID of D3020 (D 3020 010DD3 in this example). Upon successful pairing, select BT as a source and start music playback from your Bluetooth device.
A Bluetooth connection is a bit like a data pipeline between devices. Because the pipeline has a maximum width, it can sometimes be difficult to flow large audio files through it. aptX® enables CD-like quality wireless audio by solving the problem of sending the full music bandwidth over Bluetooth. aptX® has revolutionised the Bluetooth listening experience by significantly reducing the bit rate without affecting audio quality or introducing latency issues. D3020 supports aptX®.
Auto sense feature enables the D 3020 to wake up from standby mode and starts operation by selecting OPTICAL 1 source or the last digital source before going to standby mode.
The dome-shaped feet are supplied for optional installation. Install the feet as per suggested locations below. You may generate a template for proper placement of the feet.
NOTE
TV Connect is a new software enabled feature that allows the D 3020 to provide the sound for your TV. TV Connect enables D 3020 to learn the mute and volume control commands from any TV remote control. Additionally, the D 3020 will automatically power up to OPTICAL 1 source upon detection of digital TV output signal at OPTICAL 1 input.*
With TV Connect fully integrated, you can use your TV remote control to manage the following features of D 3020:
TV Connect setup requires the digital optical output of your TV to be connected to the OPTICAL 1 input of your D 3020. With this setup and with proper configuration, when you turn ON your TV, the D 3020 powers up from standby mode and the TV input (OPTICAL 1) is automatically selected.* The D 3020 can also be awakened by pressing the top panel's and the power ON button of either D 3020 remote control or TV's remote control.
The following configurations are necessary to integrate TV Connect with your D 3020.
It is recommended that you disable the TV's internal speakers so that only the D 3020 is heard. This setting is usually accessible from the TV's Setup Menu.
Consult your TV's Instruction Manual for instructions specific to your make and model of TV.
IR LEARNING PROCEDURE | |||
STEP** | D 3020 SOURCE INDICATOR BLINKS | TV REMOTE CONTROL FUNCTION KEY TO PRESS | FUNCTION LEARNED BY D 3020 FROM TV REMOTE CONTROL |
1 | OPT1 | Volume + | Volume increases |
2 | OPT2 | Volume - | Volume decreases |
3 | COAX | Mute | Mute on/off |
4 | USB | Power ON | Switch to operating mode |
* Dependent upon the D 3020 going first to standby mode after 30 minutes of inactivity.
** All four steps must be followed exactly to complete the IR Learning process.
Press and hold "" on D 3020 remote control until "OPT1" continuously blinks. Press and hold "" again until "OPT 1" stops blinking. All IR learned commands are now deleted.
AUDIO SPECIFICATIONS | |
Rated power at 8 ohms | 30W |
IHF Dynamic Power 8 ohms | 65W |
IHF Dynamic Power 4 ohms | 105W |
IHF Dynamic Power 2 ohms | 150W |
Signal-to-Noise ratio (A-weighted) | ≥ 90 dB |
Channel separation (1 kHz) | ≥ 75dB |
Channel separation (10 kHz) | ≥ 65 dB |
Channel balance | 0 ± 0.3 dB |
Frequency response (20 Hz – 20 kHz) | 0 dB to - 0.3 dB |
Total Harmonic Distortion | ≤ 0.03% |
Maximum input level | 5V |
IMD (SMPTE) | 0.02% |
GENERAL SPECIFICATIONS | |
Standby power | ≤ 0.5W |
Supports bit rate/sample rate | up to 24/192 (via Digital Audio input) up to 24/96 (via USB input) |
Unit dimensions W x H x D (Gross | 58 x 186 x 219 mm 2 5/16 x 7 3/8 x 8 5/8 inches |
Shipping weight | 2.1 kg (4.6 lbs) |
NAD SHALL NOT BE HELD LIABLE FOR ANY TECHNICAL OR USER INTERFACE DISCREPANCIES IN THIS MANUAL.
THE D 3020 OWNER'S MANUAL MAY BE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.
CHECK OUT WWW.NADELECTRONICS.COM FOR THE LATEST VERSION OF THE D 3020 OWNER'S MANUAL.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the D3020 that isn't answered in the manual? Leave your question here.