All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by TY 0864 BU CD Consumer Care...
EN 2 BJ3.1A LA Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview Index of this chapter: 1.1.3 Multimedia 1.1 Technical Specifications 1.2 Connection Overview USB input : USB2.0 (480 Mbps) 1.3 Chassis Overview Supported formats...
Page 3
Technical Specifications, Connections, and Chassis Overview BJ3.1A LA EN 3 Connection Overview 1) ONLY FOR DIGITAL SETS G_16850_002.eps 110107 Figure 1-1 Side and rear I/O connections Note: The following connector colour abbreviations are used HDMI 1 & 2: Digital Video, Digital Audio - In (acc.
Page 4
EN 4 BJ3.1A LA Technical Specifications, Connections, and Chassis Overview EXT1: Video RGB/YC - In, CVBS - In/Out, Audio - In/Out EXT2: Video RGB/YC - In, CVBS - In/Out, Audio - In/Out - Audio R 0.5 V / 1 kohm - Audio R 0.5 V...
Page 5
Technical Specifications, Connections, and Chassis Overview BJ3.1A LA EN 5 STANDBY/AUDIO MAIN SUPPLY PANEL PANEL EXTERNAL I/O PANEL CONTROL BOARD SMALL SIGNAL BOARD LED PANEL SIDE I/O PANEL G_16851_002eps 060307 Figure 1-6 PWB/CBA locations (42-inch models)
• Be careful during measurements in the high voltage • Use only lead-free soldering tin Philips SAC305 with order section. code 0622 149 00106. If lead-free solder paste is required, • Never replace modules or other components while the unit please contact the manufacturer of your soldering is switched "on".
2006 week 17). The 6 last digits contain the reduce heat. serial number. • Mix of lead-free soldering tin/parts with leaded soldering tin/parts is possible but PHILIPS recommends strongly to MADE IN BELGIUM MODEL 32PF9968/10 avoid mixed regimes. If this cannot be avoided, carefully 220-240V 50/60Hz clear the solder-joint from old tin and re-solder with new tin.
EN 8 BJ3.1A LA Mechanical Instructions 4. Mechanical Instructions Index of this chapter: Notes: 4.1 Cable Dressing • Figures below can deviate slightly from the actual situation, 4.2 Service Positions due to the different set executions. 4.3 Assy/Panel Removal •...
Page 9
Mechanical Instructions BJ3.1A LA EN 9 G_16851_004.eps 060307 Figure 4-2 Cable dressing (42-inch models)
Page 10
EN 10 BJ3.1A LA Mechanical Instructions Service Positions Important: For (older) FTV sets without these "mushrooms", it is obligatory to use the provided screws, otherwise it is possible to damage the monitor inside! For easy servicing of this set, there are a few possibilities created: •...
Page 11
Mechanical Instructions BJ3.1A LA EN 11 G_16850_010.eps 110107 Figure 4-8 Mid-range speakers Tweeters (only for 32” models) 1. Refer to next figure. 2. Unplug connectors [1]. G_16850_008.eps 3. Remove screws [2]. 110107 Figure 4-6 Side I/O board 4.3.4 IR & LED Board 1.
Page 12
EN 12 BJ3.1A LA Mechanical Instructions G_16850_012.eps 110107 Figure 4-11 Main Supply Panel (32” model)
Page 13
Mechanical Instructions BJ3.1A LA EN 13 4.3.7 Small Signal Board (SSB) and External I/O Panel Caution: it is absolutely mandatory to remount all different 2. Disconnect the mains power supply cable on the Main screws at their original position during re-assembly. Failure to Supply Panel [2].
Page 14
EN 14 BJ3.1A LA Mechanical Instructions fixation screws, while for the larger models this is hardly necessary. Therefore, you will find three separate descriptions. LCD 32” models 1. Unplug the connectors [1] from the Main Supply Panel, the LED & IR board, and the Side I/O board.
Page 15
Mechanical Instructions BJ3.1A LA EN 15 LCD 42" models 1. Unplug the connectors [1] from the LCD Inverters, the loudspeakers, the LED/IR board, the Keyboard Control board, and (carefully) from the LVDS connector on the display. 2. Remove the speaker boxes [2], to get access to the screws that hold the lower side of the metal sub-frame.
EN 16 BJ3.1A LA Service Modes, Error Codes, and Fault Finding 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: Specifications 5.1 Test Points 5.2 Service Modes Table 5-1 SDM default settings 5.3 Stepwise Start-up 5.4 Service Tools Default 5.5 Error Codes...
Page 17
Service Modes, Error Codes, and Fault Finding BJ3.1A LA EN 17 be re-written to NVM. ComPair will foresee in a possibility to do this. • Operation Hours. Displays the accumulated total of operation hours (not the stand-by hours). Every time the TV is switched "on/off", 0.5 hours is added to this number.
Page 18
EN 18 BJ3.1A LA Service Modes, Error Codes, and Fault Finding • Store. All options and alignments are stored when 5.2.3 Customer Service Mode (CSM) pressing “cursor right” and then the “OK”-button • SW Maintenance. Purpose – SW Events. Not useful for Service purposes. In case...
Page 19
Service Modes, Error Codes, and Fault Finding BJ3.1A LA EN 19 values are “Off”, “Minimum” and “Maximum”. See DFU on are fixed. So for a customer location must be set to “Home”. how to change this item. Can be changed via the installation menu (see also DFU).
Page 20
EN 20 BJ3.1A LA Service Modes, Error Codes, and Fault Finding Stepwise Start-up When the TV is in protection state due to an error detected by main software (Viper protection) and SDM is activated via shortcutting the pins on the SSB, the TV starts up and ignores The stepwise start-up method, as known from FTL/FTP sets the error.
Page 21
Service Modes, Error Codes, and Fault Finding BJ3.1A LA EN 21 Stand by or Protection Mains is applied action holder: MIPS Standby Supply starts running. +5V2, 1V2Stb, 3V3Stb and +2V5D become present. In case of PDP 3V3 Vpr to CPU PDP becomes present.
Page 22
EN 22 BJ3.1A LA Service Modes, Error Codes, and Fault Finding From part A From part A From part A From part A action holder: MIPS activate +8V6 supply action holder: St-by +8V6 error Start polling the detect-1V2 every 40ms...
Page 23
Service Modes, Error Codes, and Fault Finding BJ3.1A LA EN 23 From part A From part B From part B From part B action holder: MIPS action holder: St-by Flash to Ram image transfer succeeded within 30s? autonomous action Code = 5...
Page 24
EN 24 BJ3.1A LA Service Modes, Error Codes, and Fault Finding LCD LPL 26" WX2- SLB2 / 32 "W01- SL06 / 37"WX1- SL04 / 42"WU02-SLB1 / 42" WX3- SLA1 / 42” WX2-SLA1 / 47” WU1-SLC2 Constraints taken into account: - Display may only be started when valid QVCP output clock can be delivered by the Viper.
Page 25
Service Modes, Error Codes, and Fault Finding BJ3.1A LA EN 25 LCD LPL [26"SLB2 / 32"SL06 / 37"SL04 / 42"SLB1 / 42"SLA1] or LCD AUO [26"/32" XW02 V4/V5] / 47” WU1-SLC2 action holder: MIPS Active action holder: St-by autonomous action Mute all sound outputs.
Page 26
EN 26 BJ3.1A LA Service Modes, Error Codes, and Fault Finding Semi Stand by action holder: MIPS action holder: St-by Delay transition until ramping down of ambient light is finished. *) autonomous action *) If this is not performed and the set is...
Page 27
Service Modes, Error Codes, and Fault Finding BJ3.1A LA EN 27 Semi Stand by action holder: MIPS action holder: St-by autonomous action Reboot Power-down HDMI and 1394 hardware by keeping POWERDOWN-1394 GPIO 0 line high. Set Viper HW blocks (TM1, TM2, MBS, VMSP1 and VMSP2) to powerdown mode.
Page 28
EN 28 BJ3.1A LA Service Modes, Error Codes, and Fault Finding POD stand by Switch ON all supplies by switching LOW the ON-MODE I/O line. Full SSB power and the display related supplies become available +8V6 detected within +8V6 error...
Page 29
Service Modes, Error Codes, and Fault Finding BJ3.1A LA EN 29 action holder: MIPS transfer Wake up reasons to the Stand by µP. action holder: St-by autonomous action Images are re-transferred to DDR-RAM from Flash RAM (verification through checksum) MIPS image completes the application reload, stops DDR-RAM access, puts itself in a sleepmode and signals the standby µP when the...
Page 30
EN 30 BJ3.1A LA Service Modes, Error Codes, and Fault Finding Log the appropriate error and action holder: MIPS set stand-by flag in NVM action holder: St-by Redefine wake up reasons for protection autonomous action state and transfer to stand-by µP.
Page 31
Introduction whether the Small Signal Board (SSB) or the display of a Flat ComPair (Computer Aided Repair) is a Service tool for Philips TV is defective. Thus to determine if LVDS, RGB, and sync Consumer Electronics products. and offers the following: signals are okay.
Page 32
EN 32 BJ3.1A LA Service Modes, Error Codes, and Fault Finding Error Codes • On screen via the SAM (only if you have a picture). E.g.: – 00 00 00 00 00: No errors detected – 06 00 00 00 00: Error code 6 is the last and only 5.5.1...
Page 33
Service Modes, Error Codes, and Fault Finding BJ3.1A LA EN 33 Extra Info is logged in the NVM (that’s why this error is still mentioned • Rebooting. When a TV is constantly rebooting due to here). internal problems, most of the time no errors will be logged •...
Page 34
EN 34 BJ3.1A LA Service Modes, Error Codes, and Fault Finding 5. 1 long blink of 3 s to finish the sequence, 6. The sequence starts again. 5.6.2 How to Activate Use one of the following methods: • Activate the SDM. The blinking front LED will show the entire contents of the error buffer (this works in “normal...
Page 35
Service Modes, Error Codes, and Fault Finding BJ3.1A LA EN 35 Fault Finding and Repair Tips Read also paragraph “Error Codes” - “Extra Info”. Defective FTV For an explanation of the numbers, refer to the foot notes (on the next page)
Page 36
EN 36 BJ3.1A LA Service Modes, Error Codes, and Fault Finding Foot notes for figure “General fault find tree [1/2]”: PSU (OVP). What about the relay on the PSU? If no 1. Observe set behaviour when connecting to mains, and reaction from PSU, check fuses, Standby Supply …….
Page 37
Service Modes, Error Codes, and Fault Finding BJ3.1A LA EN 37 32" LCD Power supply start-up behaviour Power Supply Check Mains cord is connected LED is on? Check if vacation switch is closed Red LED is on +5V2 is ok.
Page 38
EN 38 BJ3.1A LA Service Modes, Error Codes, and Fault Finding 5.8.1 Exit “Factory Mode” used. In normal operation mode the value of this supply voltage will be close to +2V5 (20..30 mV difference). • The supply voltages +5V and +8V6 are available from When an "F"...
Page 39
1. Disconnect the TV from the Mains/AC Power. SSB must be ordered, due to the presence of the security 2. Press the "OK" button on a Philips DVD RC-6 remote keys!!! (copy protection keys, MAC address, for US the POD control (it is also possible to use the TV remote in "DVD"...
Page 40
EN 40 BJ3.1A LA Service Modes, Error Codes, and Fault Finding 2. Short circuit the SPI pins [2] on the SSB. They are located outside the shielding (see figure “SPI service pads”). 3. Keep the SPI pins shorted while connecting the TV to the Mains/AC Power.
Block Diagrams, Test Point Overviews, and Waveforms BJ3.1A LA 6. Block Diagrams, Test Point Overviews, and Waveforms Wiring Diagram ME7 WIRING 32” (STYLING ME7) 8305 8306 8735 8364 1M02 8317 1736 1735 MAIN SUPPLY STANDBY / AUDIO INVERTER INVERTER LVDS...
Block Diagrams, Test Point Overviews, and Waveforms BJ3.1A LA Block Diagram Audio AUDIO DVB-T: TUNER MPIF MAIN: AUDIO SOURCE SELECTION PNX2015 MPIF MAIN: MPIF MAIN: AUDIO LEFT RIGHT PROTECTION / AUDIO AMPLIFIER CONNECTIONS B MUTE CONTROL 7C00 7J00 1M02 PNX3000HL...
Block Diagrams, Test Point Overviews, and Waveforms BJ3.1A LA Block Diagram Control & Clock Signals CONTROL & CLOCK SIGNALS VIPER: CONTROL USB 2.0: HOST VIPER: A/V + TUNNELBUS PNX2015: DV I/O INTERFACE PACIFIC3: PART 2 7N00 7V00 7G04 ISP1561BM PNX8550EH...
Page 46
Block Diagrams, Test Point Overviews, and Waveforms BJ3.1A LA Test Point Overview SSB (Top Side) I137 A2 IJ20 C1 I156 A2 IJ29 C3 I548 E4 IJ36 C3 I549 E4 IJ36 C3 I550 E4 IJ37 C3 I551 G2 IK95 B3 I552 D2...
Page 47
Block Diagrams, Test Point Overviews, and Waveforms BJ3.1A LA Test Point Overview SSB Part 1 (Top Side) Part 1 G_15960_055ta.eps 310306...
Page 48
Block Diagrams, Test Point Overviews, and Waveforms BJ3.1A LA Test Point Overview SSB Part 2 (Top Side) Part 2 G_15960_055tb.eps 310306...
Page 49
Block Diagrams, Test Point Overviews, and Waveforms BJ3.1A LA Test Point Overview SSB (Bottom Side) F181 E4 F284 G4 FB22 C1 FLB7 C2 FU01 G4 I157 A2 I260 G4 I363 F1 I466 C4 IA28 B3 IH13 E2 IK87 A2 IP29 G1...
Page 50
Block Diagrams, Test Point Overviews, and Waveforms BJ3.1A LA Test Point Overview SSB Part 1 (Bottom Side) Part 1 G_15960_056ta.eps 310306...
Page 51
Block Diagrams, Test Point Overviews, and Waveforms BJ3.1A LA Test Point Overview SSB Part 2 (Bottom Side) Part 2 G_15960_056tb.eps 310306...
Block Diagrams, Test Point Overviews, and Waveforms BJ3.1A LA I2C Overview I²C DVB-T: TUNER MPIF MAIN: VIPER: CONTROL HDMI HDMI: I/O + CONTROL B10A COMMON INTERFACE: PART1 EXTERNALS B CONNECTIONS B +3V3 3Q11 SDA-MM SDA-MM-BUS1 SDA-MM-BUS1 I2C1-SDA 3Q10 SCL-MM SCL-MM-BUS1...
Page 94
Circuit Diagrams and PWB Layouts BJ3.1A LA SSB: Common Interface: Part 2 2P44 B3 COMMON INTERFACE: PART 2 2P50 C1 B10B 2P51 E1 3P02 C3 3P03 A3 +3V3 3P04 B3 3P05 A3 3P07 A4 3P07 CI or no POD-RDC VCCEN...
Page 95
Circuit Diagrams and PWB Layouts BJ3.1A LA SSB: Common Interface: Part 3 2P31 A3 2P32 C3 COMMON INTERFACE: PART 3 B10C B10C 2P33 E7 2P76 A7 2P77 C7 +3V3 3P60-1 B4 3P60-2 C3 +3V3 3P60-3 C4 3P76 3P60-4 C3 +3V3...
Alignments BJ3.1A LA EN 133 8. Alignments Index of this chapter: Notes: 8.1 General Alignment Conditions • All changes must be stored manually. 8.2 Hardware Alignments • If an empty NVM (permanent memory) is detected, all 8.3 Software Alignments settings are set to pre-programmed default values.
Page 133
EN 134 BJ3.1A LA Alignments 8.3.3 White Point • Set “Active control” to “Off” as earlier described. • Choose “TV menu”, “TV Settings” and then “Picture” and put: – “Dynamic contrast” to “Off”. – “Colour enhancement” to “Off”. – “Light sensor” to “Off”.
Page 134
Alignments BJ3.1A LA EN 135 Option Settings 8.4.1 Introduction The microprocessor communicates with a large number of I ICs in the set. To ensure good communication and to make digital diagnosis possible, the microprocessor has to know which ICs to address. The presence / absence of these specific ICs (or functions) is made known by the option codes.
Page 135
EN 136 BJ3.1A LA Alignments Menu-item Subjects Options Description Audio Repro Acoustic System (Cabinet None design, used for setting Entry ME5 5W dynamic audio parameters). Entry ME5 15W (Soft) Wrap Entry+ (ME7) etc..Centre mode support Feature present / not present...
Page 136
3 (8) China IF 0= Off, 8= On 4 (16) Interconnect Alternative Tuner 0= Philips, 16= Alps Tuner make. 5 (32) Tuner Type 0= TD1336s (B-Chassis US), 32= TD1331(J-Chassis US), 64= UV1318 Tuner type (B-chassis US is e.g (analogue EU), 96= TD1316 (Hybrid EU) "BP2.3U").
Page 137
EN 138 BJ3.1A LA Alignments Bit (dec. Byte value) Subject Options Settings (in decimal values) Remarks 0 (1) Display Screen see Table “Display code overview” in Chapter “Service Modes” for the values Screen size, type, and resolution. 1 (2) 2 (4)
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ3.1A LA EN 139 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets Index of this chapter: 9.1.2 Chassis Block Diagram 9.1 Introduction 9.2 Power Supply Description below refers to the block diagrams in chapter 6 9.3 Front-End...
Page 139
EN 140 BJ3.1A LA Circuit Descriptions, Abbreviation List, and IC Data Sheets SSB Cell Layout LVDS DISPLAY INTERFACE DC / DC & CONV SOURCE SELECTION SIGNAL PROCESSING MPIF RS232 COMMON INTERFACE TUNER UART HDMI 1 HDMI 2 G_15960_112.eps 070306 Figure 9-1 SSB top view...
Page 140
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ3.1A LA EN 141 Power Supply Common Interface (CI) 9.2.1 DC/DC converters 9.4.1 Introduction For a (more) detailed description of the on-board DC/DC The digital sets of this chassis are provided with a special slot converters of the SSB see the BP2.xU Service Manual.
Page 141
EN 142 BJ3.1A LA Circuit Descriptions, Abbreviation List, and IC Data Sheets Conditional Access Working Principle 9.4.3 Communication Channels The Conditional Access Module (CAM), also called POD (Point Of Deployment), is a removable CAM, implementing the In Band (IB) Conditional Access (CA) system for a Host (i.e. the TV set).
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ3.1A LA EN 143 Abbreviation List Colour Transient Improvement: manipulates steepness of chroma transients 0/6/12 SCART switch control signal on A/V CVBS Composite Video Blanking and board. 0 = loop through (AUX to TV), 6...
Page 143
EN 144 BJ3.1A LA Circuit Descriptions, Abbreviation List, and IC Data Sheets enabled for HDCP "software key" Non-Volatile Memory: IC containing decoding. TV related data such as alignments HDMI High Definition Multimedia Interface Open Circuit Head Phone Out Of Band channel Monochrome TV system.
Page 144
4.406250 MHz and 4.250000 MHz Sound Intermediate Frequency SMPS Switched Mode Power Supply Sync On Green SOPS Self Oscillating Power Supply S/PDIF Sony Philips Digital InterFace SRAM Static RAM Small Signal Board STBY STandBY Sync On Green SVGA 800x600 (4:3)
EN 146 BJ3.1A LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.10 IC Data Sheets This section shows the internal block diagrams and pin configurations of ICs that are drawn as "black boxes" in the electrical diagrams (with the exception of "memory" and "logic"...
Page 146
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ3.1A LA EN 147 9.10.2 Diagram B2A, TD1316AF (IC 1T05) Block Diagram G_15960_139.eps 100306 Figure 9-9 Internal block diagram 9.10.3 Diagram B2B, TDA10046AHT (IC 7T17) Block Diagram G_15960_140.eps 100306 Figure 9-10 Internal block diagram...
Page 147
EN 148 BJ3.1A LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.10.4 Diagram B3x, PNX3000HL (IC 7C00) Block Diagram 1 × CVBSOUTA CVBSOUTB 2NDSIFEXT (FMRAD) SIFAGC CVBSOUTIF MIXER SIFIN 2nd SIF internal & AM SND DEMOD DTV 1st IF...
Page 148
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ3.1A LA EN 149 9.10.5 Diagram B4x, PNX2015E (IC 7J00) Block Diagram 16-BIT 225 MHz DDR PNX2015 MEMORY CONTROLLER video NORTH TUNNEL SOUTH TUNNEL PNX8550 coprocessor HD input (TDA9975) MEMORY VO-1 BASED SCALER...
Page 149
EN 150 BJ3.1A LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.10.6 Diagram B4A, CY2305SC-1 (IC 7J08) Block Diagram Pin Configuration CY2305SC-1 CLKOUT CLKA1 SOIC Top View CLKA2 CLKOUT CLK4 CLK2 CLKA3 CLK1 CLK3 CLKA4 CLKB1 Select Input CLKB2...
Page 150
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ3.1A LA EN 151 9.10.8 Diagram B5x, PNX8550EH (IC 7V00) Block Diagram Streaming Interface Optional External 32-Bit 225 MHz DDR from Tunnel Video Improvement Processing PNX8550 Memory 30 (dig) DVD-CSS 5-Layer Controller...
Page 151
EN 152 BJ3.1A LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.10.9 Diagram B5A, LM3526MX (IC 7Q01) Block Diagram Pin Configuration LM3526-L F_15400_134.eps 230905 Figure 9-16 Internal block diagram and pin configuration...
Page 152
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ3.1A LA EN 153 9.10.10 Diagram B7B & B7C, TDA9975EL (IC 7B11) Block Diagram τ ORR/V τ I²C ORB/U τ ORG/Y G/Pb B/Pb1 B/Pb2 B/Pb3 I²C 10/12 I²C I²C CLAMP BIAS I²C I²C...
Page 153
EN 154 BJ3.1A LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.10.11 Diagram B8, ISP1561BM (IC 7N00) Block Diagram SMI# SEL48M PME# ISP1561BM GLOBAL CONTROL IRQ1 IRQ12 legacy keyboard and mouse support AD[31:0] PCI CORE KBIRQ1 C/BE#[3:0] REQ# MUIRQ12...
Page 154
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ3.1A LA EN 155 9.10.12 Diagram B10A, TPS2211AIDB (IC 7P00) Block Diagram TPS2211A Card B V CC1 3.3 V V CC2 3.3 V V pp1 12 V V pp2 See Note A...
Page 155
EN 156 BJ3.1A LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.10.13 Diagram B10A, STV0701 (IC 7P03) Block Diagram Pin Configuration F_15400_138.eps 240505 Figure 9-20 Internal block diagram and pin configuration...
Page 156
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ3.1A LA EN 157 9.10.14 Diagram C, TDA8925ST (IC 7701) Block Diagram V DD2 V DD1 TDA8925ST/J TDA8926J BOOT1 DRIVER HIGH CONTROL OUT1 HANDSHAKE DRIVER REL1 STAB temp V SS1 TEMPERATURE SENSOR...