MULTIQUIP AR13H Operation Manual
  1. Manuals
  2. Brands
  3. MULTIQUIP Manuals
  4. Construction Equipment
  5. AR13H
  6. Operation manual
MULTIQUIP AR13H Operation Manual

MULTIQUIP AR13H Operation Manual

Ride-on tandem drum roller parallel drive system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATION MANUAL
MODEL AR13H
RIDE-ON TANDEM DRUM ROLLER
PARALLEL DRIVE SYSTEM
(HONDA GX610K1QZB2 GASOLINE ENGINE)
Revision #16 (06/22/21)
To find the latest revision of this publication or
associated parts manual, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

Advertisement

Table of Contents
loading

Related Manuals for MULTIQUIP AR13H

Summary of Contents for MULTIQUIP AR13H

  • Page 1 OPERATION MANUAL MODEL AR13H RIDE-ON TANDEM DRUM ROLLER PARALLEL DRIVE SYSTEM (HONDA GX610K1QZB2 GASOLINE ENGINE) Revision #16 (06/22/21) To find the latest revision of this publication or associated parts manual, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

  • Page 2: Proposition 65 Warning

    PROPOSITION 65 WARNING PAGE 2 — AR-13H RIDE-ON TANDEM DRUM ROLLER — OPERATION MANUAL — REV. #16 (06/22/21)

  • Page 3: Table Of Contents

    TABLE OF CONTENTS MULTIQUIP AR-13H RIDE-ON TANDEM DRUM ROLLER Proposition 65 Warning ..........2 Table Of Contents ............. 3 Safety Message Alert Symbols ......4-5 Rules For Safe Operation ........6-8 Operation and Safety Decals ....... 9-10 Specifications (Roller) ..........11 Specifications (Engine) ...........

  • Page 4: Safety Message Alert Symbols

    WARNING - LETHAL EXHAUST GASES NOTE instructions for the safe and efficient Gasoline engine exhaust gases contain operation of the Multiquip Model poisonous carbon monoxide. This gas is AR-13H Ride-on Tandem Drum colorless and odorless, and can cause Roller. Refer to the engine manufacturers instructions for data death if inhaled.
  • Page 5 AR-13H RIDE-ON ROLLER — SAFETY MESSAGE ALERT SYMBOLS WARNING - ROTATING PARTS CAUTION - RESPIRATORY HAZARDS NEVER operate equipment with covers, or guards removed. Keep fingers , hands , ALWAYS wear approved respiratory hair and clothing away from all moving protection.

  • Page 6: Rules For Safe Operation

    . questions or information. ■ NEVER use accessories or attachments, which are not recommended by Multiquip for this equipment. Damage to the equipment and/or injury to user may result. ■ Manufacturer does not assume responsibility for any accident due to equipment modifications.
  • Page 7 RULES FOR SAFE OPERATION ■ NEVER Run engine without air cleaner. Severe engine MAINTENANCE SAFETY damage may occur. ■ NEVER lubricate components or attempt service on a running ■ ALWAYS read, understand, and follow procedures in machine. Operator’s Manual before attempting to operate equipment. ■...
  • Page 8 RULES FOR SAFE OPERATION LOADING AND TRANSPORTING SAFETY EMERGENCIES ■ ALWAYS know the location of the DANGER - Loading & Unloading the Roller nearest fire extinguisher . DANGER! ALWAYS load and unload the roller on Level, Hard Ground, or Pavement. Serious injury or death can result from improper loading, lifting or unloading.

  • Page 9: Operation And Safety Decals

    OPERATION AND SAFETY DECALS Machine Safety Decals The AR-13H Ride-on Tandem Drum Roller is equipped with a number of safety decals. These decals are provided for operator safety and maintenance information. The illustration below and on the next page shows these decals as they appear on the machine. Should any of these decals become unreadable, replacements can be obtained from your dealer.
  • Page 10 OPERATION AND SAFETY DECALS PAGE 10 — AR-13H RIDE-ON TANDEM DRUM ROLLER — OPERATION MANUAL — REV. #16 (06/22/21)

  • Page 11: Specifications (Roller)

    AR-13H RIDE-ON ROLLER — SPECIFICATIONS (ROLLER) l l o c i f ) . g ) . g i t a ) . g i t a a l l ) . g l l a . n i l l a .

  • Page 12: Specifications (Engine)

    AR-13H RIDE-ON ROLLER — SPECIFICATIONS (ENGINE) i f i o i t - r i r t S e v l i l y , ) n i l o t s i p s i . n i r t S .

  • Page 13: Dimensions

    AR-13H RIDE-ON ROLLER — DIMENSIONS (Side View) (Rear View) Figure 1. AR-13H Roller Dimensions . n i r e t . n i . n i , t f . n i . n i l l a h t i .

  • Page 14: General Information

    AR-13H RIDE-ON ROLLER — GENERAL INFORMATION The roller nominally has an operating weight of 3,088 lbs (1,400 The AR-13H roller has been designed for asphalt application Kg.), but can be increased to 3,309 lbs (1,500 Kg.) by adding and compaction of granular soils used in site preparation. Use water ballast to the rear drum.
  • Page 15 To prevent damage to the engine after a rollover, the roller must NOT be started. NEVER start a roller after a rollover. CONTACT your nearest authorized multiquip dealer for instructions or servicing. AR-13H RIDE-ON TANDEM DRUM ROLLER — OPERATION MANUAL — REV. #16 (06/22/21) — PAGE 15...

  • Page 16: Roller Components

    AR-13H RIDE-ON ROLLER — ROLLER COMPONENTS 12 13 Figure 4. Roller Components 1 PAGE 16 — AR-13H RIDE-ON TANDEM DRUM ROLLER — OPERATION MANUAL — REV. #16 (06/22/21)
  • Page 17 AR-13H RIDE-ON ROLLER — ROLLER COMPONENTS Figure 4 shows the location of the components and basic 12. Rear Spray Control Valve – This valve controls the components for the AR-13H compaction roller. The function of flow of water to the rear spray bar .Turn the water valve each component or control is described below: to the open position (counterclockwise) to let water flow, Battery –...
  • Page 18 AR-13H RIDE-ON ROLLER — ROLLER COMPONENTS Figure 5. Roller Components 2 Figure 5 shows the location of additional components for the 34. Steering Cylinder – Controls direction of roller. AR-13H compaction roller. The function of each component or 35. Engine – This unit incorporates a HONDA GX-610, air control is described below: cooled engine rated at 18 hp at 3,500 rpm.

  • Page 19: Engine Components

    AR-13H RIDE-ON ROLLER — ENGINE COMPONENTS Figure 6. Honda GX610 Engine Controls and Components INITIAL SERVICING Oil Filler Cap – Remove to add engine oil. The engine (Figure 6) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturer's engine Oil Dip Stick –...

  • Page 20: Inspection

    AR-13H RIDE-ON ROLLER — INSPECTION Before Starting 3. Check the oil level shown on the dipstick (Figure 8). 1. Read safety instructions at begining of manual. 2. Clean the ROLLER , removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner. 3.
  • Page 21 AR-13H RIDE-ON ROLLER — INSPECTION 4. If the fuel level is low, remove the fuel fillercap/guage and fill Fuel Check with unleaded gasoline. Wipe up any spilled fuel immedi- ately. DANGER - EXPLOSIVE FUEL 5. Pay attention to the fuel tank capacity when replenishing NEVER fill the fuel tank while the engine is running or in fuel (Figure 12).
  • Page 22 AR-13H RIDE-ON ROLLER — INSPECTION Battery Check A 12-volt DC battery (Figure 16) is shipped dry, and will require a proper electrolyte level for operation. ALWAYS be sure that the battery cables are properly connected to the battery terminals as shown below. Generally the RED cable will be connected to the positive terminal of the battery, and the BLACK cable will be connected to the negative terminal of the battery.

  • Page 23: Initial Start-Up

    AR-13H RIDE-ON ROLLER — INITIAL START-UP Initial Start-up Instructions PUSH-IN, THEN PULL Starting TO SET THROTTLE (RPM’s) CAUTION - General Operation Safety DO NOT attempt to operate the roller until the Safety, General Information and Inspection sections have been read and understood.

  • Page 24: Operation

    AR-13H RIDE-ON ROLLER — OPERATION OPERATION 3. Try manuvering the roller a few times to get familar with the handling. Also place the travel lever in the oposite direction Parking Brake to get acquainted with driving in reverse. 1. To release the parking brake, press and hold the release 4.

  • Page 25: Maintenance

    AR-13H RIDE-ON ROLLER — MAINTENANCE Maintenance Perform roller maintenance as indicated by Figure 25 and Table 5. Figure 25. Roller Maintenance Schedule y l i c i l c i l i r p r e l t l i .
  • Page 26 AR-13H RIDE-ON ROLLER — MAINTENANCE HYDRAULIC OIL HYDRAULIC OIL Hydraulic Oil System CAP/FILLER PORT SUCTION FILTER The hydraulic system consists of a two pump stack directly coupled to the engine. A hydraulic valve block (manifold)is provided for quick and easy testing and troubleshooting. Hydraulic oil is filtered by a screen filter located in the tank filler neck, a 40 micron suction filter located in the tank, and a 10 micron return filter , with cold oil bypass valve located in the...
  • Page 27 AR-13H RIDE-ON ROLLER — MAINTENANCE The vibration circuit is controlled by an electric control valve CAUTION - Freewheel Engagement Valve located on the valve block (manifold). This valve is controlled by the “ ON/OFF ” pushbutton switch mounted on top of the travel The freewheel engagement valve (towing) is only for lever.
  • Page 28 AR-13H RIDE-ON ROLLER — MAINTENANCE Forward/Reverse Hydraulic Pressure Test On the manifold block install a 5,000 psi pressure gauge to quick disconnect test port 1. Park the machine on a solid flat surface and stop the engine. Set the parking brake and block the front drum securely . Start the engine and run at full throttle.
  • Page 29 AR-13H RIDE-ON ROLLER — MAINTENANCE Forward/Reverse Relief Valves Drive Adjustment Steering Relief Valve Pressure Adjustment The forward and reverse relief valves (Figure 35) are shim To adjust the relief valve steering pressure perform the following: type cartridge type and are located in the hydrostatic pump (not Insert an 8 mm allen wrench into steering relief port 4 on the manifold block) under plugs 1 and 2 .
  • Page 30 AR-13H RIDE-ON ROLLER — MAINTENANCE Removing and Replacing Hydrostatic Pump Drums and Main Frame Set the parking brake. The front drum is designed to apply vibration and compaction force to the operating surface for compaction. This vibration and Disconnect the battery. compaction force is produced when the vibrator shaft is rotated.
  • Page 31 AR-13H RIDE-ON ROLLER — MAINTENANCE STEP 1 STEP 4 STEP 3 STEP 2 1. JACK FRAME UP SLIGHTLY AT 3. MARK AND DISCONNECT ARTICULATION JOINT. HOSES FROM MOTOR AND MANIFOLD. 2. REMOVE THE FOUR ALLEN HEAD SCREWS HOLDING THE SIDE 4.
  • Page 32 AR-13H RIDE-ON ROLLER — MAINTENANCE STEP 1 STEP 4 STEP 3 STEP 2 1. JACK FRAME UP SLIGHTLY AT 3. MARK AND DISCONNECT ARTICULATION JOINT. HOSES FROM MOTOR. 2. REMOVE THE EIGHT ALLEN HEAD 4. REMOVE FOUR ALLEN HEAD SCREWS HOLDING THE SIDE SCREWS FROM DRUM SUPPORT COVER OF THE DRUM SUPPORT PLATE.
  • Page 33 AR-13H RIDE-ON ROLLER — MAINTENANCE STEP 6 STEP 4 STEP 2 STEP 5 STEP 1 STEP 3 STEP 4 1. JACK FRAME UP SLIGHTLY AT REMOVE ALLEN HEAD SCREWS ARTICULATION JOINT. HOLDING THE SIDE COVER OF THE DRUM SUPPORT PLATE. 2.
  • Page 34 AR-13H RIDE-ON ROLLER — MAINTENANCE Alternator/Regulator The AR-13H is equipped with a 20 amp charging system. This system uses three charge coils connected in parallel. The windings of each coil are wound with heave-duty insulated wire and are further protected by insulating material for long life. A voltage regulator is provided to control the amount of charge voltage being delivered to the 12 volt electrical system.

  • Page 35: Preparation For Long-Term Storage

    AR-13H RIDE-ON ROLLER — PREPARATION FOR LONG-TERM STORAGE Roller Storage For storage of the roller for over 30 days, the following is recommended:  Drain the fuel tank completely, or add STA-BIL to the fuel.  Run the engine until the fuel in the injection system is completely consumed.

  • Page 36: Manifold Test Ports

    AR-13H RIDE-ON ROLLER — MANIFOLD TEST PORTS Figure 29. Manifold Test Ports PAGE 36 — AR-13H RIDE-ON TANDEM DRUM ROLLER — OPERATION MANUAL — REV. #16 (06/22/21)

  • Page 37: Hydraulic System Diagram

    AR-13H RIDE-ON ROLLER — HYDRAULIC SYSTEM DIAGRAM Figure 30. Hydraulic System Diagram AR-13H RIDE-ON TANDEM DRUM ROLLER — OPERATION MANUAL — REV. #16 (06/22/21) — PAGE 37...

  • Page 38: Electric Wiring Diagram (S/N 241001 And Below)

    AR-13H ROLLER — ELECTRIC WIRING DIAGRAM (S/N 241001 AND BELOW S/N 241001 AND BELOW Figure 31. Electrical Diagram PAGE 38 — AR-13H RIDE-ON TANDEM DRUM ROLLER — OPERATION MANUAL — REV. #16 (06/22/21)

  • Page 39: Electric Wiring Diagram (S/N 241002 And Above)

    AR-13H ROLLER — ELECTRIC WIRING DIAGRAM (S/N 241002 AND ABOVE S/N 241002 AND ABOVE AR-13H RIDE-ON TANDEM DRUM ROLLER — OPERATION MANUAL — REV. #16 (06/22/21) — PAGE 39...

  • Page 40: Hydraulic Hose Connections

    AR-13H RIDE-ON ROLLER — HYDRAULIC HOSE CONNECTIONS MANIFOLD FROM OPERATOR’S FRONT RIGHT SIDE POSITION FRONT LEFT SIDE FROM OPERATOR’S POSITION NOTES HOSES SHADED FOR VISUAL CLARITY. Figure 32. Hydraulic Hose Connections 1 PAGE 40 — AR-13H RIDE-ON TANDEM DRUM ROLLER — OPERATION MANUAL — REV. #16 (06/22/21)
  • Page 41 AR-13H RIDE-ON ROLLER — HYDRAULIC HOSE CONNECTIONS FRONT RIGHT MOTOR STEERING COLUMN MANIFOLD REAR LEFT MOTOR FROM OPERATOR’S POSITION NOTES FRONT LEFT MOTOR HOSES SHADED FOR VISUAL CLARITY. Figure 33. Hydraulic Hose Connections 2 AR-13H RIDE-ON TANDEM DRUM ROLLER — OPERATION MANUAL — REV. #16 (06/22/21) — PAGE 41...

  • Page 42: Troubleshooting (Roller)

    AR-13H RIDE-ON ROLLER — TROUBLESHOOTING (ROLLER) r b i i t a c i l c i l . e r a t l t l o l o s r b i i t a t i w l i o r o f i t n .

  • Page 43: Troubleshooting (Engine)

    AR-13H RIDE-ON ROLLER — TROUBLESHOOTING (ENGINE) g n i j n i t c e n o i l e u r i t l e u e t s c e f v i t l e u c a l l e u e t l i g o l...
  • Page 44 AR-13H RIDE-ON ROLLER — TROUBLESHOOTING (ENGINE) t l i f . r e l i f r e t t l i f . r e n i t y l e g i t e r i l o r v e l r o f e r r...
  • Page 45 NOTES AR-13H RIDE-ON TANDEM DRUM ROLLER — OPERATION MANUAL — REV. #16 (06/22/21) — PAGE 45...
  • Page 46 © COPYRIGHT 2021, MULTIQUIP INC. Multiquip Inc , the MQ logo and the Mayco logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.

Table of Contents