Connections; Connecting To A Tv - Toshiba SD-24VESE Service Manual

Connections

Tips
Depending on your TV and other equipment you wish
to connect, there are various ways you could connect
the unit.
Please refer to the manuals of your TV, Stereo
System or other devices as necessary to make the
best connections.
For better sound reproduction, connect this unit's
AUDIO OUT jacks to the audio in jacks of your
amplifier, receiver, stereo or audio/video equipment.
See "Connecting to Optional Equipment" on page 12.
Caution
– Make sure this unit is connected directly to the TV.
Set the TV to the correct video input channel.
– Do not connect this unit's AUDIO OUT jack to the
phono in jack (record deck) of your audio system.

Connecting to a TV

Make one of the following connections, depending on
the capabilities of your existing equipment.
When using the SCART's RGB signal, set the video
output switch to RGB. When using the COMPO-
NENT/PROGRESSIVE SCAN VIDEO OUT jacks, set
the video output switch to COMPONENT.
RGB signal is only exclusive for DVD playback.
Basic connection (AV)
1 1
Connect the EURO AV1 AUDIO/VIDEO on the rear
panel of this unit to the SCART input socket on the
TV using a SCART lead.
For TV without SCART, connect the yellow VIDEO
OUT jack and DVD/VCR AUDIO OUT jacks of this
unit to the TV.
2 2
Some TV broadcasters transmit encoded television
signals which you can only see with a purchased or
rented decoder. You can connect such a decoder
(descrambler) to this unit.
Basic connection (RF)
1 1
Connect the RF antenna cable from your indoor/
outdoor antenna to AERIAL jack on the rear panel
of this unit.
2 2
Connect the supplied RF antenna cable from the
RF.OUT (DVD/VCR OUT) jack on the rear panel of
this unit to your television's Antenna Input.
S-Video connection
1 1
Connect the S-VIDEO OUT jack on this unit to the
S-Video in jack on the TV using the S-Video cable
(not supplied).
2 2
Connect the Left and Right AUDIO OUT (DVD
EXCLUSIVE OUT) jacks of this unit to the audio
left/right in jacks on the TV using the audio cables.
Component (Color Stream
(ColorStream ® pro) Video connection
(DVD EXCLUSIVE OUT)
1 1
Connect the COMPONENT/PROGRESSIVE SCAN
VIDEO OUT/(DVD EXCLUSIVE OUT) jacks on the
DVD+VCR to the corresponding in jacks on the TV
using an Y Pb Pr cable (not supplied).
2 2
Connect the Left and Right AUDIO OUT (DVD
EXCLUSIVE OUT) jacks of the DVD+VCR to the
audio left/right in jacks on the TV using the audio
cables.
Notes
If your television is a high-definition or "digital ready" televi-
sion, you may take advantage of the DVD+VCR's progres-
sive scan output for the highest video resolution possible.
Set the Progressive Scan to "On" on the setup menu for pro-
gressive scan signal, see page 19.
When you use Component Video signal (interlace mode), set
the Progressive Scan to "Off" on the setup menu.
If you set Progressive Scan to ON in error, you must reset
the DVD+VCR. First, remove the disc in the DVD+VCR.
Next, press STOP (x) and hold it for five seconds before
releasing it. The video output will be restored to the standard
setting, and a picture will once again be visible on a conven-
tional analog TV or monitor.
Progressive scan on does not work with the analog video
connections (yellow VIDEO OUT jack or S-VIDEO OUT
jack).
If the TV has an S-video input, connect the DVD player with
the S-video cable. When using an S-video cable, do not con-
nect the yellow video cable.
Rear of this unit (Component/Progressive scan Video connection)
AERIAL VIDEO IN COMPONENT/PROGRESSIVE SCAN VIDEO INPUT
Pr Pb
Rear of this unit (Basic connection)
1-16
® ) / Progressive Scan
Rear of TV
AUDIO INPUT SCART INPUT
Y L R
S-VIDEO OUT
Satellite or Set Top Box