Hazard Identification; Model Number Description; Overview Of Manual; Kit Inspection - Trane BAYSENS019C Installer's Manual

Hazard Identification

Warnings and Cautions appear at
appropriate sections throughout this
manual. Read these carefully.
WARNING
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
CAUTION
Indicates a situation that may result
in equipment or property-damage-
only accidents.

Model Number Description

All products are identified by a
multiple-character model number
that precisely identifies a particular
type of unit. Its use will enable the
owner/operator, installing
contractors, and service engineers to
define the operation, specific
components, and other options for
any specific unit.
When ordering replacement parts or
requesting service, be sure to refer to
the specific model number and serial
number printed on the unit
nameplate.

Overview of Manual

Note: One copy of this document
ships inside each
Programmable Zone Sensor
kit and is customer property.
The unit's maintenance
personnel must retain it.
This booklet describes step-by-step
instructions for installing and
© 2007 American Standard Inc. All rights reserved
Preface and Warnings and Cautions
programming the Programmable
Zone Sensor.
By carefully reviewing the
information within this manual and
following the instructions, the risk of
improper operation and/or
component damage will be
minimized.
Should equipment failure occur,
contact a qualified service
organization with qualified,
experienced HVAC technicians to
properly diagnose and repair this
equipment.
Note: The procedures discussed in
this manual should only be
performed by qualified,
experienced HVAC
technicians.

Kit Inspection

Upon receipt of the kit, immediately
note;
• Any visible damage to the
exterior shipping package.
Record any damage on the
shipping documents.
– Specify the type and extent of
the damage on the "bill of
lading" before signing.
• Unpack the contents and
carefully inspect it for obvious
damage due to shipment.
• If concealed damage has
occurred, notify the carrier's
terminal of the damage
immediately by phone and by
mail. Concealed damage must
be reported within 15 days.
• Do not remove damaged
material from the receiving
location. Take photos of the
damage, if possible. The owner
must provide reasonable
evidence that the damage did
not occur after delivery.
• Check for material shortages.
Within the package you should
find;
– 1 - Sensor Module,
– 1 – Package of mounting
hardware, and;
– 1 - Installation and operation
manual.
Contact the Parts Center nearest your
area should there be any damaged or
missing components.
Note: 20 - 130 Ton IntelliPak: In
order for setpoints provided
by the ZSM to be recognized
by the unit, setpoint source
selections at the Human
Interface must be set to NSB
SETPOINT INPUT.
Remote Panel w/ NSB -
BAYSENS019C
This 7 day programmable sensor
features 2,3 or 4 periods for Occupied
or Unoccupied programming per
day. If the power is interrupted, the
program is retained in permanent
memory. If power is off for an
extended period of time, only the
clock and day may have to be reset.
The programmable sensor is
compatible for use with UCP mirco
control, ReliatelTM mirco control or
IntelliPakTM control systems.
The Zone Sensor allows selection of
four system modes (Heat, Cool, Auto,
and Off), two fan modes (On and
Auto). It has dual temperature
selection with programmable start
time capability.
The occupied cooling set point
ranges between 45 and 98 degrees
Fahrenheit. The heating set point
ranges between 43 and 96 degrees
Fahrenheit.
A liquid crystal display (LCD) displays
zone temperature, temperature set
points, day of the week, time, and
operational mode symbols.
The Option Menu is used to enable or
disable applicable functions, i.e.;
Morning Warm-up, Economizer
minimum position override during
unoccupied status, Fahrenheit or
Centigrade, Supply air tempering,
Remote zone temperature sensor, 12/
24 hour time display, Smart fan, and
Computed recovery.
During an occupied period, an
auxiliary relay rated for 1.25 amps @
30 volts AC with one set of single
pole double throw contacts is
activated.
ACC-SVN28A-EN