Onkyo TX-NR809 Instruction Manual page 32

3
When you've finished making the settings, press
ENTER.
MultEQ XT: Auto Setup
Speakers Type(Front)
Powered Zone 2
Subwoofer
Perform the "Speaker Setup" according to your
speaker configuration:
– Speakers Type(Front)
– Powered Zone 2
– Subwoofer (➔
If you use a powered subwoofer(s), go to step 4. If
not, go to step 5.
When an optional unit is connected to the
UNIVERSAL PORT jack on the AV receiver, the
optional unit setting may appear on the speaker
setting menu.
4
Adjust the subwoofer volume level to 75 dB, and
then press ENTER.
Test tones are played through the subwoofer. Use the
volume control on the subwoofer.
Note
• If your subwoofer does not have a volume control,
disregard the displayed level and press ENTER to proceed
to the next step.
• If you set the subwoofer's volume control to its maximum
and the level displayed is lower than 75 dB, leave the
subwoofer's volume control at its maximum and press
ENTER to proceed to the next step.
5
Use q/w to select "Audyssey Quick Start" or
"Audyssey MultEQ XT Full Calibration".
6
Press ENTER.
Audyssey MultEQ
Speaker Setup starts.
Test tones are played through each speaker as
Audyssey MultEQ XT Room Correction and Speaker
Setup runs. This process takes a few minutes. Please
refrain from talking during measurements and do
not stand between speakers and the microphone.
Do not disconnect the speaker setup microphone
during Audyssey MultEQ XT Room Correction and
Speaker Setup, unless you want to cancel the setup.
If you select "Audyssey Quick Start", you will go to
step 9.
7
Place the setup microphone at the next position,
and then press ENTER.
Audyssey MultEQ XT performs more measurements.
This takes a few minutes.
8
When prompted, repeat step 7.
En
32
AUDYSSEY
Normal
No
Yes
page 47)
(➔
(➔ page 47)
page 48)
® XT Room Correction and
9
Use q/w to select an option, and then press
ENTER.
MultEQ XT: Auto Setup
-- Review Speaker Configuration --
Subwoofer
Front
Center
Surround
Front Wide
Front High
Surround Back
Surround Back Ch
Save
Cancel
The options are:
Save:
Save the calculated settings and exit
Audyssey MultEQ XT
.
Speaker Setup
Cancel:
Cancel Audyssey MultEQ XT
.
and Speaker Setup
Tip
• You can view the calculated settings for the speaker
configuration, speaker distances, and speaker levels by
using e/r.
10
Use q/w to select a target, and use e/r to change
the setting.
After the results of Audyssey MultEQ XT have been
saved, the menu will display the "Audyssey"
(➔ page 53), "Dynamic EQ"
"Dynamic Volume" (➔
Note
• When "Audyssey Quick Start" has been used for
measurement, "Audyssey" cannot be selected.
• These settings are applied to all input selectors.
11 Press ENTER.
12 Disconnect the speaker setup microphone.
Note
• You can cancel Audyssey MultEQ XT Room Correction and
Speaker Setup at any point in this procedure simply by
disconnecting the setup microphone.
• Do not connect or disconnect any speakers during
Audyssey MultEQ XT Room Correction and Speaker Setup.
• If the AV receiver is muted, it will be unmuted automatically
when Audyssey MultEQ XT Room Correction and Speaker
Setup starts.
• Changes to the room after Audyssey MultEQ XT Room
Correction and Speaker Setup requires you run
Audyssey MultEQ XT Room Correction and Speaker Setup
again, as room EQ characteristics may have changed.
AUDYSSEY
: Yes
: 100Hz
: 40Hz
: 100Hz
: None
: None
: 120Hz
: 2ch
Room Correction and
Room Correction
(➔ page 53),
page 53) settings.