Configuring Various Settings; Network Setup Menu - Onkyo TX-NR900 User Manual

Configuring Various Settings

Navigating through the Setup Menu:
Be sure to press the RCVR button before using the remote controller.
1. Press the SETUP button.
2. Using the and cursor buttons, select the menu
that you want to enter.
3. Press the ENTER button to enter the selected menu.
4. Use the and cursor buttons to select the sub-menu
that you want to enter and press the ENTER button.
Each sub-menu has different settings that can be changed as desired,
and they are all explained in the pages that follow. To change a
setting, first select it using the
change the setting using the
5. Press the RETURN button to set the new settings and
return to the previous menu screen.
Press the RETURN button again to return to the main menu.
Input Setup Menu (When NET AUDIO is selected
as the input source)
When NET AUDIO is selected as the input source, you can set up Music
Server on this screen.
2-1.Music Server
Input:NET A
a.Select Server
:My PC-ABCDE
→
OK
Quit:|SETUP|
2-1. Music Server Sub-menu
a. Select Server
Select a network server that exists on the network.
* mark appears to the servers detected on the network. If there is a server
which does not have * mark, make sure that the server is started.
After selection, use the button to select "→ OK", and press the
ENTER button to confirm your selection.
2-2. Playback OSD Display Sub-menu
a. Playback OSD Display
Full: Select this when you want to have the OSD display the
information on the currently played track.
Simple: Displays the current track information summary in two
lines.
Off: Select this when you do not want to have the information
displayed on the OSD.
6
and cursor buttons, and then
and cursor buttons.
2-2.Playback OSD Display
Input:NET A
a.Playback OSD Display
:Full
Quit:|SETUP|

Network Setup Menu

Before you can use the TX-NR900/900E to play music contained in the
music library on the Net-Tune server and listen to Internet radio, you
must correctly configure the TX-NR900/900E's network settings so that
it can connect to your LAN and the Internet.
It is strongly recommended to use a broadband connection (via an xDSL
or CATV leased line) and a router. If you are connected to the Internet
via a narrowband dialup connection, you may not be able to enjoy
Internet radio as you expect or at all.
Before setting up the TX-NR900/900E, make sure that you are already
using a router that provides Internet access and that the TX-NR900/900E
is correctly connected with your router or hub via a LAN cable.
For more information on Internet connectivity, consult with your ISP
(Internet Service Provider) or refer to the documentation of your router.
Advanced Menu
5.Network Setup
5-1.IP Address
1.Speaker Config
2.Speaker Distance
a.DHCP/AUTO-IP :On
3.Level Calibration b.IP Address
4.Bass Peak Level :192.168. 9. 62
c.SUBNET Mask
:255.255.255. 0
d.Gateway
:192.168. 9. 1
DNS Server |ENTER| Quit:|OSD|
e.1st:210.134.143. 7
f.2nd:125. 40.104. 0
Advanced Menu
5.Network Setup
1.IP Address
2.Proxy Setup
3.MAC Address
4.Client Setup
→Save settings
|ENTER|Quit:|SETUP|
Advanced Menu
5.Network Setup
5-4.Client Setup
1.Speaker Config
2
.Speaker Distance
a.Client Name
3.Level Calibration :TX-NR900 0102
4.Bass Peak Level b.Wakeup on LAN
:On
uit:|OSD|
c.NTSP Port
:XXXXXX
Quit:|SETUP|
DHCP (Dynamic Host Configuration Protocol) and AutoIP are
mechanisms for network configuration, which assign IP addresses
automatically to the network devices such as the TX-NR900/900E, PC,
and broadband router.
DNS (Domain Name System) is a mechanism which translates domain
names into IP addresses or vice versa. Domain names such as
www.onkyo.co.jp are used for Web browsing, and IP addresses such as
210.199.170.69 are used for actual network data transfer.
Advanced Menu
5.Network Setup
5-2.Proxy Setup
1.Speaker Config
2.Speaker Distance
3.Level Calibration a.Proxy Server
4.Bass Peak Level
:On
b.Proxy Address
c.Proxy Port
: 8080
|ENTER| Quit:|OSD|
Quit:|SETUP|
Advanced Menu
5.Network Setup
5-3.MAC Address
1.Speaker Config
2
.Speaker Distance a.MAC Address
3.Level Calibration :XX:XX:XX:XX:XX:XX
4.Bass Peak Level
Quit:|OSD|
Quit:|SETUP|