Contents For your safety This equipment has been designed and For your safety ......... 1 manufactured to meet international safety stan- dards but, like any electrical equipment, care Important Information ......4 must be taken if you are to obtain the best Remote Control Buttons ......
Page 3
IF IN DOUBT PLEASE CONSULT A COMPE- this. Special arrangements may need to be TENT ELECTRICIAN. made for infirm or handicapped people. DO DONT continue to operate the equipment if you are in any doubt about it working normally, DO read the operating instructions before you or it is damaged in any way ...
Page 4
WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING Fingers may be trapped under the TV causing injuries. Hold the TV at the bottom in the middle, and do not allow the stand to tilt up or down.
Important Information Please take note EXCLUSION CLAUSE JVC shall under no circumstances be liable for loss and/or damage to the product caused fire; earthquake; accidental damage; intentional misuse of the product; use of the product in improper conditions;...
Remote Control Buttons / I = (Stand By) button TV / VCR / DVD Switch Number buttons AV button (TV, EXT-1, EXT-2, EXT-2 S, EXT-3, EXT-3 S or BLUE / PICTURE Mode button YELLOW / Sleep Timer button MENU button = Cursor Up button OK button = Cursor Right button...
Using the stand This TV comes with a Table Top Stand already attached. This stand can be used to adjust the direction of the TV screen. Tilt the TV up and down: While holding the stand with one hand which should be on lower level of the stand for avoiding trapping, use your other hand to hold the middle of the of the TV and slowly tilt the TV up and down.
Installing TV on the wall WARNING When you install the TV on the wall, only use a JVC wall mounting unit (optional) which is designed for this TV. Make sure that the TV is installed on the wall by a skilled installer.
NTSC Playback. Preparation PLL (Channel Search) Install Display on solid horizontal surface such PC input (Support Up to 1024 x 768) as a table or desk. Before Switching on your TV For ventilation, leave a space of at least 10 cm free all around the set.
How to connect other devices Switching the TV ON/OFF IMPORTANT: Switch off the TV before connect- To switch the TV on ing any external device. Your TV will switch on in two steps: Sockets for external connections are at the Connect the power supply cord to the sys- back of the TV.
APS menu appears. To use T-V Link functions APS, searches and sorts all channels and A T-V Link compatible VCR means a JVC stores them automatically on your TV, accord- video cassette recorder with the T-V Link logo, ing to the transmission of programme sys- or with one of the following logos.
If FEATURE NOT AVAILABLE is displayed, Operating the TV download was not performed correctly. Before You can operate your TV using both the re- trying to download again, check that: mote control handset and onset buttons. The VCR power is turned on. Volume setting and programme selection can ...
Menu System Your TV has been designed with a menu sys- tem to provide an easy manipulation of a multi- function system. The TV is controlled by choos- ing the commands, which are displayed on the screen. MAIN MENU Programme Selection (Previous or next programme) Press the MENU...
Page 15
Setting Colour Setting Contrast Using or button select Colour. Using or button select Contrast. Press button to increase colour level. Press button to increase contrast level. ...
Page 16
Note 1: Or you can directly change the volume set- At low signal level, the changings on the Noise Reduction tings using + (to increase) or - (to function are not effective when there is menu on the screen. decrease) button.
Page 17
You can also change sound mode directly Selecting Menu Language pressing I-II button on your remote control. Using or button select Language. In case of bilingual broadcast (Dual Sound), Press or button to select menu lan- you can select original or dubbed language guage.
Page 18
Selecting Programme EXT-2 output will be chosen as TV mode only and any scrambled channels will be un- Using or button select Programme. scrambled through decoder connected your To select programme number, you can use TV via EXT-2 output.
Page 19
Program Menu is used to delete a channel, to To change the programme number of a change the programme number of a channel, channel (Insert) to give a channel name to a channel, and to 1. Choose the channel you want to change start the A.P.S (Autostore) function.
on the required item. The selected mode In stereo transmission it yields a phase differ- comes automatically on the screen. ence between left and right channels. Hyper Sound selection will be displayed on the 6RXUFH 79 screen when the TV Status button is pressed or programme is changed.
Page 21
No-Signal Detection (TV mode) Zoom Modes If no valid signal detected, it takes 5 minutes Zoom mode can be changed by pressing Red to switch to the Stand-By mode unless any button. You can change the screen size ac- signal detected or any Remote Control com- cording to the picture aspect ratio.
Auto Position PC Mode If you shift the picture horizontally or vertically Installation to an unwanted position, use this item to put the picture into correct place automatically. Power off both Computer and Display before making any connections. Select Auto position item by using ...
Page 23
PC Picture Menu Sound in PC mode In the Main menu, select PC Picture using Connect the PCs Audio output to the TVs PC or button, then enter the PC Picture Audio In socket with an audio cable. menu pressing ...
buttons. The page will be searched and the Teletext page number will be displayed on the upper Teletext is an information system that displays left corner of the screen when the selected text on your TV screen. Using the Teletext in- page is found.
Teletext page number will be displayed on Peripheral Equipment the upper left corner of the screen when the Connections selected page is found. There is a wide range of audio and video equip- Press button to display the selected ment that can be connected to your TV.
Page 26
Via the ANT (aerial) socket NTSC Playback If your equipment does not have an Eurocon- Connect a NTSC video recorder to a terminal. nector or RCA jacks, connect it to the TV with Then press AV button to select the corre- an aerial cable.
PC Input Typical Display Modes The display has a maximum resolution of 1024 x 768, vertical sync. frequency range of 50-75 Hz and a horizontal sync. frequency range of 30-69 KHz. The following table is an illustration of some of the typical video display modes. 5HVROXWLRQ )UHTXHQF\ 0RGH...
PC Picture Tips If no PC picture appears, check that the D- Can not turn the TV on? SUB cable is connected properly. Check that Check that TV/VCR/DVD switch is set to TV your PCs resolution set correctly. See page position.
Specifications Model Item LT-20B60SU Broadcasting Systems PAL SECAM BG, DK, I, L, Lp Channels and VHF (VL) : 46,25 MHz - 168,25 MHz Frequencies VHF (VH) : 175,25 MHz - 463,25 MHz UHF : 471,25 MHz - 863,25 MHz Cable TV : (S1-S20/ S21-S41) Input Signal Video: Analog 0,7 Vp-p 75 ohm positive Sync: TTL Level positive or negative, Seperate sync.
Page 32
This file has been downloaded from: www.UsersManualGuide.com User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes.. Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide, manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product, documentation manual, user maintenance, brochure, user reference, pdf manual Downloaded from:...