Dimplex DXSRF2 Installation And Operating Instructions

Model : DXSRF2
Dimensions
(millimetres)
Model(s) Specification
DXSRF2 2.0kW Thermostat & Switch
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
IMPORTANT SAFETY ADVICE
DO NOT use the heater on deep pile carpets or the long hair type
of rugs, or less than 750mm (30") away from any overhanging
surface. Keep combustible materials such as drapes and other
furnishings clear from the front, sides and rear of the heater. Do
not use heater to dry your laundry.
DO NOT use the heater in the immediate surroundings of a bath,
a shower, a swimming pool or any other water filled receptacle.
DO NOT place the heater directly below a fixed socket outlet.
The socket-outlet must be accessible at all times to enable the
mains plug to be disconnected as quickly as possible.
DO NOT COVER or obstruct the air inlet and outlet openings
in any way.
Never touch live parts! Danger to life!
Never operate the appliance with wet hands! Danger to life!
This appliance is not suitable for connection to permanent wiring.
The heater must be on a flat stable surface when in use.
DO NOT operate the heater with the mains lead overhanging the
front outlet grille.
The appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experienceand knowledge, unless they have been given
supervision or instruction concerning the use of the appliance by a
person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
The appliance is designed to self-right itself if it is accidentally
knocked over, however the appliance should not be maltreated
to perform this function.
ALWAYS ENSURE THE APPLIANCE DOES NOT COME TO REST ON
THE MAINS LEAD OR ALLOW THE LEAD TO BECOME WRAPPED
AROUND THE APPLIANCE - THIS MAY IMPAIR THE SELF-RIGHT
FUNCTION.
NEVER leave the heater unattended when it is used by or near the
aged, infirm person's or children.
IMPORTANT - The heater carries a 'DO NOT COVER' warning
to alert the user to the risk of overheating that exists if the
heater is accidentally covered.
The Instruction leaflet belongs to the appliance and must be kept
in a safe place. If changing owners, the leaflet must be surrendered
to the new owner.
Never use the appliance if the appliance or cord is damages -
RISK OF INJURY.
IMPORTANT – If the mains lead of this appliance is damaged, it
must be replaced by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
WARNING: In order to avoid a hazard due to inadvertent resetting
of the thermal cut-out, this appliance must not be supplied through
an external switching device, such as a timer, or connected to a
circuit that is regularly switched on and off by the utility.
Fan Heater
H W
265 230
Installation and Operating Instructions
D
(see Fig. 3)
230
Electrical connection
This heater must be used on an A.C
on the heater must correspond to the supply voltage. This heater is fitted
with a plug incorporating a 13 amp fuse.
When replacing the fuse, a 13 amp fuse approved by ASTA to BS 1362
must be used.
If the plug is not suitable for the socket outlets in your home, the plug must
be cut off and an appropriate one fitted. A plug cut off from a mains lead
will give a shock hazard if inserted into a 13 amp socket elsewhere in the
house. To avoid this, it should be disposed of immediately.
NOTE: The fuse cover of a non-rewirable plug must be refitted when
changing the fuse. Should the cover become lost, the plug must not be
used until the correct replacement fuse cover is obtained from your supplier
or by contacting our customer helpline.
IMPORTANT : The wires in this mains lead are coloured in accordance
with the following code :
BLUE :
BROWN :
As the colours of the wires in the mains lead may not correspond with the
coloured markings in your plug, proceed as follows :
Connect the BROWN wire to the terminal marked 'L' or coloured RED.
Connect the BLUE wire to the terminal marked 'N' or coloured BLACK.
Note : 'L' or 'N' must not be connected to the EARTH terminal marked
'E' or or coloured GREEN or GREEN AND YELLOW.
If in doubt, consult your electrician.
Using the Heater
- see Fig. 2
Heat Control
Fig. 2
see Fig. 3
Thermostat Control -
Fig. 3
The heater will now cycle on and off to maintain your selected room
temperature. An audible click may be heard when the thermostat operates
- this is normal.
Note : If the heater does not come on when the thermostat is at a low
setting, this is normally because the room is warmer than the thermostat
setting and is not a fault.
* When the heat control is set to '
control to maximum.
Position ' ' will turn the heater on and off to maintain a temperature of
approximately 5°C.
08/52719/0
(see Fig. 2)
Fig. 1
.~
supply only and the voltage marked
NEUTRAL
LIVE
- OFF
- Cool Blow*
- Half heat
- Full heat
The heat output is controlled by the
thermostat, according to the room
temperature.
Turn the thermostat knob fully clockwise
to maximum setting initially. When the
room is warm enough, reduce the setting
slowly until the heater just clicks off.
' for cool blow, set the thermostat
Issue 0